E-Plex 411BAM
6Pages

411BAM Series Battery Auctioneering Module Introduction The E-Plex 411BAM has been designed to simplify electronic systems wiring by monitoring the voltage and current on each of the port and starboard batteries and auctioneering or selecting whichever has the highest voltage available for critical device operations. 3 solid state outputs are capable of driving link solenoids and emergency bilge pumps from either the port or starboard battery bank. The 411BAM can be used with 12 or 24 volt batteries and will provide status information of each battery including the current draw (up to 100A) of that battery. 4 nickel plated brass M8 terminals are provided for main feeds and the distribution feeds. Local electronic override capabilities allow independent operation of the device loads. For additional safety, during a thermal runaway condition a thermal disconnect is used to remove power from the solid state outputs. Key Features Design Specifications • • • • • • Shock: Mil Std 202 Method 213 test condition 1 • ibration: Tested to Lloyds Register Approval V Vibration Test 2 • ransient voltage suppression: EN6100-6-1 T • oisture resistance: IP66 M • CB characteristics: UL94V-0 P • ower distribution: UL 1077 compliant (except highP voltage dielectric test) • gnition protection: UL 1500 compliant I • alt spray: Tested to Lloyds Register Approval Salt S Spray Test • perating Temperature: -40°C to 60°C O • torage Temperature: -40°C to 85°C S • perating Humidity: 0% to 100% (condensing) O • eight: 1.65 lb (750g) W 2 solid state outputs capable up to 5 amps each 1 solid state output capable up to 12 amps total P ORT & STBD power monitoring L ocal electronic override capabilities 2 active high inputs for PORT & STBD battery switch status indications • rovides current sensing of loads P • hermal, short circuit, and programmable T overload protection • LEN value 2 Powering systems - Empowering designers

411BAM Series Electrical Specifications Description Min Nominal Max Absolute Max (Surge) Voltage 7 VDC 12 / 24 VDC 32 VDC 45 VDC2 Current, Total5 0.025 A – 12 A1 160 A2 Sleep / Storage7 10 µA – 100 µA – Current, per channel 3, continuous 0 – 12 A 80 A4 Current, per channel 3, intermittent duty3 0 – 15 A 80 A4 Inrush capable, channel 3 – – 80 A 80 A4 Current, per channel 1 & 2, continuous 0V – 5A 70 A4 Current, per channel 1 & 2, intermittent duty3 0V – 7.5 A 70 A4 Inrush capable, channel 1 & 2 – – 25 A 70 A4 Lead inductance 0V – 100 µH6 – 0V – 20 mH – 5 Load Inductance, channel 3 9 Load...

411BAM Series Trip Speed Characteristics Wiring Specifications Pin # Pin Description Pin # Pin Description A1 Digital Input 2 M8-T1 Main PORT Battery Feed E1 Digital Input 1 M8-T2 Main STBD Battery Feed B1 Solid State Fused Output 3 F1 Battery Return M8-T3 PORT Battery Distribution Feed M8-T4 STBD Battery Distribution Feed C1 Solid State Fused Output 2 G1 Solid State Fused Output 1 D1 E-Plex Data Bus + H1 E-Plex Data Bus – Solid State Outputs 1 & 2: 0 to 5A, 7-32VDC Solid State Outputs 3: 0 to 12A, 7-32VDC Battery Power (+): 0.02A to 100A, 7-32VDC Status LEDs: ON - Channels 2-4: Load ON;...

411BAM Series Pin Specifications Female Terminal Cable Range AWG (mm2) Terminal Insulation Range 18-16 (1.0-0.75 mm2) 15304716 1.70-2.25 mm 16-12 (2.50-1.50 mm2) 15304717 2.20-3.00 mm Seal Insulation Range Seal P/N 1.20-1.85 mm 15366063 1.85-2.25 mm 15356064 2.09-2.66 mm 15366061 2.70-3.2 mm 15336674 Typical Wiring Diagram Fuse / Disconnect, as required per ABYC / RVIA (100A max) + 12VDC or 24VDC, STBD Battery Bank STBD Load / Battery Charger Active High Digital Input 1 13 5 M8 - T2 4 M8 - T4 Active High Digital Input 2 13 Ch. 3 A1 Emergency Bilge Pump E1 Ground B1 Status LEDs, Channels 1-5...

Powering Systems - Empowering Designers George Summers Close, Medway City Estate, Rochester, Kent ME2 4EL tel: +44 (0)1634 778704 Fax: +44 (0)1634 290773 email: sales@e-plex.co web: www.e-plex.co Important Notice: E-Plex Ltd. (E-Plex) reserves the right to make changes to or discontinue any product or service identified in this publication without notice. E-Plex advises its customers to obtain the latest version of the relevant information to verify, before placing any orders, that the information being relied upon is current. E-Plex assumes no responsibility for infringement of patents or...