413DWM
6Pages

Hexa Multi Module, Diode Protected The E-PLEX® 413DWM is a six channel DC power distribution module capable of handling loads of up to 15A per channel or 50A total. The six channels can be utilized as either inputs, outputs, or a combination of both. The individual channels may be combined in order to handle larger amperage loads. With four diode protected channels the module and E-Plex system are protected from being back-feed. While required for many multi-speed motor applications, this protection is required in applications where the module is wired in parallel with a system that may be powered by an additional external source. An example of this includes a bilge pump controlled by a float switch along with an E-Plex module. Local electronic override capabilities allow independent operation of the device loads. In addition, the 413DWM design allows for the ability to utilize up to two channels as dimmer circuits, providing a flexible solution for lighting without requiring additional external dimming hardware. Design Specifications 6 channels with outputs capable to 15 amps each (50 amps total) 4 channels are diode protected against back feeding 2 channels with PWM dimming capabilities Reverse battery protected Status LED's for each channel Thermal, short circuit, and programmable overload Local electronic override capabilities Designed for motor loads Shock : Mil Std 202 Method 213 test condition 1 Vibration : Tested to Lloyds Register Approval Vibration Transient voltage suppression : EN6100-6-1 Power distribution: UL 1077 compliant (except high- voltage dielectric test) Ignition protection: UL 1500 compliant Salt spray: Tested to Lloyds Register Approval Salt Spray Operating Humidity: 0% to 100% (condensing) Powering systems - Empowering designers

Electrical Specifications Electrical Specifications Screw assembly to a flat mounting surface in 2 places, as shown in the Mounting Instructions Imperial (English) fasteners: Use #10 size screw, #10 split lock washer, #10 washer. Torque to 20-22 in-lb. Do not exceed this torque as it could cause Metric fasteners: Use M5 size screw, M5 split lock washer and M5 washer. Torque to 250-280 N-cm. Do not exceed this torque as it could cause 1. De-rate max current by 0.2 A per °C above ambient, 25°C 2. Measured at 8.3 ms single half sine wave. (JEDEC Method) 3. Duty cycle at 1 minute on time, 5...

Trip Speed Characteristics Wiring Specifications The first two outputs (CI, BÍ) are PWM capable and may be used to dim lighting loads. Channels Al and B2 through D2 incorporate a diode to protect against back-feeding from an external source. Status LEDs: ON - Channels 1-6 indicates Load ON, E-Plex channel indicates module responding OFF - Channels 1-6 indicates Load OFF, E-Plex channel indicates module not responding10 BLINKING - Channels 1-6 indicates Load FAULT, E-Plex channel indicates module responding Power / Battery Connections: Must be fused. Maximum wire size should be sized based...

413DWM Series Pin Specifications Female Terminal Cable Range AWG (mm2) Terminal Insulation Range 18-16 (1.0-0.75 mm2) 15304716 1.70-2.25 mm 16-12 (2.50-1.50 mm2) 15304717 2.20-3.00 mm Seal Insulation Range Seal P/N 1.20-1.85 mm 15366063 1.85-2.25 mm 15356064 2.09-2.66 mm 15366061 2.70-3.2 mm 15336674 Typical Wiring Diagram E-Plex + E-Plex – A2 M5 - T2 E2 Ch. 6 F2 Ch. 5 B2 13 Motor Ch. 4 G2 C2 13 Status LEDs, Channels 1 - 6 and E-Plex10 Motor H2 D213 Pump M5 - T1 A113 Pump E1 E-Plex Lamp B1 Ch. 3 F1 C1 Ch. 2 G1 Ch. 1 H1 D1 Lamp E-Plex – E-Plex + Fuse / Disconnect, as required per ABYC / RVIA...

Dimensional Diagram Mechanical Specifications J1 - Brown: Mates to Delphi P/N 15317308 J2 - Blue: Mates to Delphi P/N 15317304 Cavity Plug: Power Stud Connections: M5 nickel plated brass Ordering Information Powering systems - Empowering designers

413DWM Series BATTERY 325QMM, 366HMM, 422QMM & 436MMX : 4, 6 or 10 channel multi-modules for control of lighting, including dimming and user-defined “mood” lighting POWER INVERTER 400ECM, 450ECM & 500CCM : Electronic control modules (“clocks”) that function as the master controller and programmer of the entire E-Plex system 361SIM : Inverter interface for complete control over your inverter functions 345LCD, 350LCD & 452LCD : 5.7”, 10” & 12” color LCD touchscreen displays that allow the user to interface with the E-Plex system, including monitoring and control functionality and includes...