PT 130 CATALOGUE
7Pages

2008 - 2009 P R O D U C T C ATA LO G Cook Manufacturing Corporation A Division of Marine Accessories Corporation 3920 South 13th Duncan, OK 73533 Tel: 800.654.3697 Fax: 580.252.2970 www.cook-mfg.com Quality and innovative marine products from these Marine Accessories Corporation companies: QUALITY PRODUCTS l PRECISION MACHINING Authorized CMC Dealer in this area: THE MARKET LEADER IN TRANSOM JACKS & TILT AND TRIMS Cook Manufacturing Corporation - Since 1956 Duncan, Oklahoma ©2007 Part #5080 Revision K

Our Customers’ Thoughts... “Your company makes one strong jackplate. I am impressed with the product that you build and will always own a CMC jackplate.” Hydraulic Power-Lift® Transom Jacks There are more CMC Power-Lifts on the B.A.S.S. tournament trail than any other jackplate. Pros have found superior quality and dependability with the CMC Power-Lift. Question? 5 1/2" SET-BACK MODEL PL-65* (#65001 - w/ gauge #65002 - w/o gauge Why should I purchase a hydraulic power-lift transom jack for my boat? Answer. Patrick K. – Michigan Improved performance for your outboard engine! In order for...

Convenient Exterior Mounting Provides Ease of Installation! Marine Electric Hydraulic System non-ferrous material which makes it more impervious to salt water Stainless steel 3/4"pin with aluminum-bronze alloy rollers. The roller is highly impact resistant, corrosive resistant and has a high load carrying capacity This patented design virtually eliminates any chance of binding which is common with other transom jacks. Great for fresh or salt water use. For over 20 years, most Power-Lift sales have been in a salt water environment. completely self-contained with its own fluid reservoir...

Transom Jacks Manual Power-Lift Jack lift transom jack has the hydraulic lift without automated adjustment. performance enhancement, but don't have the budget for our hydraulic unit then looking for.Our manual units provide similar benefits to the hydraulic units. However, since you cannot raise or moving you will not receive enhancements associated with a hydraulic unit. Manual Features: • Made of 6061 T6 extruded aluminum alloy • Stainless steel fasteners for maximum • Centrally located adjustment screw for positive alignment •5 1/2" Set Back from Transom • Designed to fit standard B.I.A....

POWER DIAL This calibrated height control allows you to dial in Power-Lift.The Power-Lift will raise or lower to that indicator lamps illuminate on/off switch to allow you The power dial accessory can only be added to a hydraulic power-lift with a position indicator gauge already TRANSOM WASHER PLATES Made of strong 3/8" 6061 T6 alloy aluminum (not cast aluminum), the CMC transom washer can eliminate bolts "biting" into transoms and can more evenly distribute loads on high performance engines. Hole centers:Top Bottom Washer Plate (#20032) CUSTOM WASHER PLATES The top washer plate can be...

Question? Are CMC tilt n’ trim systems easy to install? 90 Degrees of Tilt and Trim Answer. Lonnie S. – Minnesota “The PT-130 works like a dream and the performance is great! Now I can go fishing by myself and load my boat without ruining the prop in shallow water.” Corky C. – Missouri “At the lake I was somewhat hesitant at first to use the throttle too hard or too fast. After a while, I did everything possible to test the unit. I couldn’t be more pleased and satisfied with its performance.” Russ S. – Indiana 10 CMC Product Catalog 1 Year Hydraulic System Warranty Incredible Durability The...

2008 - 2009 P R O D U C T C ATA LO G Cook Manufacturing Corporation A Division of Marine Accessories Corporation 3920 South 13th Duncan, OK 73533 Tel: 800.654.3697 Fax: 580.252.2970 www.cook-mfg.com Quality and innovative marine products from these Marine Accessories Corporation companies: QUALITY PRODUCTS l PRECISION MACHINING Authorized CMC Dealer in this area: THE MARKET LEADER IN TRANSOM JACKS & TILT AND TRIMS Cook Manufacturing Corporation - Since 1956 Duncan, Oklahoma ©2007 Part #5080 Revision K