PRODUCT CATALOGUE
1 / 7Pages

Serving the Marine Industry Since 1975 CMC MARINE • PRODUCT INSERT MARINE ACCESSORIES 2012-2013 Marine Accessories Catalog

Serving the Marine Industry Since 1975 Hydraulic Power-LirV Transom Jacks The High Speed Power-Lift Js the newest addition to the product fine* The model PL-6SHS High Speed Power-Lift will raise V-6 300 h.p. and $mo!kr outboard motor* in approximately S seconds which is twice as fast as the regular that has been in the market since 1982. Ideai for those who want a jack plate for high speed positioning of their outboard motor. MODEL PL-fiS-lQHS MOUNTING HARDWARE INCLUDED WITH CMC LIFTS, The Model PL-S5 is rated for V-6 and smaller motors. Not designed for V*B motors or racing applications....

Serving the Marine Industry Since 1975 Our most popvlor mode J, t be PL-6S is toted for V-6 and smaller motors end provides 5" of vertical travel. It is not designed for VB motors or racing applications. See model PL -65S5. The same rugged lift system as our PL-6S units with the addition of 1/2" stainless steel motor rails that give this jack the strength and power to lift V6 and i/B engines of 300hp max. The solid stainless rails have no castings or welds to break making this the strongest jack in our lineup. The rotter assembly contains a stainless steel 3/4" pin with aluminum-bronze...

Serving the Marine Industry Since 1975 Manual Power-Lift* Transom jacks Manual Features; ■ Made of 6061 T6 extruded aluminum alloy • Stainless steel fasteners for maximum • Centrally located adjustment screw for positive alignment ■5 1/2" Set Back from Transom ■ Designed to fit standard B.i.A. bolt pattern withoui dnll holes or making mod if cations in the boat or motor. With CMC, you con adjust your provides the added convenience bottom. Most competitive brands can only be adjusted 2012-2013 Marine Accessories Catalog

Serving the Marine Industry Since 1975 Static Set Back Plates Th<? 7 FNCH STATIC SET BACK PLATE transom bracket and 1 inch of adjustment on the motor bracket. The dimension from motor side is 3 1/2 inches. The 9 »NCH STATIC SET BACK PLATE also has 1 1 /2 inches of adjustment at the transom and 1 inch of adjustment on the motor bracket.The dimension from the top of the transom to the top of the motor side MOUNTING HARDWARE INCLUDED WITH • These Models are toted far V-6 and smaller motors. Not designed for V-8 motors or racing applications. inches higher than the 1 from prop to jet drive....

Serving the Marine Industry Since 1975 Electric Hydraulic Tilt N' Trim You Get Power Tilt & Trim, Better Boat Handling, More Speea\ Lower Fuel Consumption and No More Back Strain! • Bated For 130 H.R and Smaller Motors. * t>* Set Back 10 Enhance Boat Stability and Performance. • 20° of Trim and a Total of 90u of Tilt and Trim. * 1/2* 6061 T6 Extruded Aluminum Construction with Stainless Steel Fasteners, • Electric Hydraulic Actuator Rated at 7353 lbs, of Thrust! • Standard B.I A Bolt Hole Pattern, • Convenient Adapter Kit Available for Clamp-on Motors. * Four Stainless Steel Motor Mounting...

Serving the Marine Industry Since 1975 TRANSOM CLAMP MOTOR ADAPTER For installation of motors mounted with transom damps, an adapter kit is available from CMC.This adapter kit is made for quick and easy installation of these type motors. The photo above shows this adapter on a PT-130 with a transom clamp motor If 13023 ^BBjj ^e QP,,anQt tilt ant! trim ^^^^^^^^ i5Ci;rj^iiiiir iiwiiabte ixirh the B£3S)S% sealed and drip proof convenient height determination. The sending unit Is completety sealed and waterproof, which eliminates any moif tare problems. The up-down toggle fw#(h Is standard...