Catalogs >
Cobham >
NETNODE IP Mesh Radio Phase Three Plain

NETNODE IP Mesh Radio Phase Three Plain
3Pages

Catalog excerpts

NETNODE IP Mesh Radio Phase Three Plain - 1

NETNode IP Mesh Radio Phase 3 (Plain) COFDM – Video, Audio Telemetry and IP Products September 2012 Data Sheet The most important thing we build is trust Cobham NETNode IP mesh radios are the latest innovations in the expanding range of Cobham Tactical Communications The NETNode can be connected to third party cameras and Surveillance solutions that feature Cobham technology using the NETAV option. Alternatively, there are dedicated PTZ camera solutions available for direct connection to the at their core. NETNode e.g. CAMPTZ* is a high performance, high quality NETNode IP radios can be combined in a fluid self-forming, day/night PTZ camera for long range and overt surveillance. self-healing mesh containing up to twelve radios. The The CAMPTZ* option requires the NETAV option to be NETNode radios within the mesh exchange data on a single fitted. frequency, simplifying frequency management. The entire mesh occupies just 2.5MHz of bandwidth (3.0, 3.5, 5.0 and 6.0MHz also available). The NETNode radios employ the unique Cobham COFDM modulation scheme and therefore offer excellent RF penetration and performance in the presence of multipath. The NETNode mesh radios can provide over 5.0 (6.0)Mb/s of IP data (data rate depends on mode, number of nodes and range between nodes). This available IP data rate can be used to exchange IP data traffic between nodes. The highly flexible mesh topology means that data can be exchanged between nodes in a point-to-point or multi-point fashion; range can be extended by using nodes as repeaters. The self-forming, self-healing mesh architecture makes the NETNode product ideal for use in mobile surveillance applications, command and control, or advanced robotics. Security of the entire mesh network can be ensured by the use of the optional AES128 or AES256 encryption. Control of the deployed mesh is achieved using the inbuilt web browser or comprehensive Mission Commander PC application. This software suite, based around a mapping display, is used to configure and monitor the mesh, and to control its nodes and cameras. Video can be viewed on the PC device using the Mission Commander software or, if IP Hardware Decoder devices are employed, video can be viewed on conventional monitors and recorded on conventional recorders. Mission Commander is now officially released with Milestone compatibility for data storage and retrieval.

Open the catalog to page 1

NETNODE IP Mesh Radio Phase Three Plain - 2

NETNode IP Mesh Radio Phase 3 (Plain) COFDM – Video, Audio Telemetry and IP Products September 2012 Data Sheet Specification: Encryption Interfaces RF Interfaces (Antenna 1 and 2) Power Data interface RS232/RS485 data input (shared with user camera control) 1K2 to 115K2 baud switchable With UDP and TCP routing protocol Non Line of Sight Light urban 500-700m PTZ camera interface (with AVI fitted) Non Line of Sight Light urban 800-1400m User camera type User camera control From Mesh Commander PC application using VISCA, PELCOD or PELCO-P From any user supplied desk controller Requires RS232...

Open the catalog to page 2

NETNODE IP Mesh Radio Phase Three Plain - 3

NETNode IP Mesh Radio Phase 3 (Plain) COFDM – Video, Audio Telemetry and IP Products September 2012 Data Sheet Product Codes: Connectors Power: Female Lemo 4 pin 0B Female Lemo 3 pin (Data) Ethernet Ethernet Ethernet Ethernet Female Lemo 3 pin 0B (for RS232 input when encoder is fitted) IP Mesh Node 1.40GHz (excl IP Mesh Node 2.38GHz (excl (excl Ants, incl PSU) Ethernet OP Ethernet ON Ethernet IP Ethernet IN RS485 TX+ RS485 TXGND RS485 RX+ RS485 RX+12V Engineering use RS232TX1 Engineering use RS232RX1 GNS RS232 Control TX2 RS232 Control RX2 GND N/C N/C GND GND RX TX PLUS the following two...

Open the catalog to page 3

NETNODE IP Mesh Radio Phase Three Plain 3Pages

Catalog excerpts

All Cobham catalogs and brochures

NETNODE IP Mesh Radio Phase Three Plain
3Pages