Cat 3306B DITA Propulsion
40Pages

Shown with Accessory Equipment Engine Weight, Net Dry (approx) .. 1120.9 kg (2469 lb) STANDARD EQUIPMENT_ Dry, regular duty air cleaner Cooling System Gear driven centrifugal jacket water pump, engine oil cooler, expansion tank, thermostats and housing, transmission oil cooler Exhaust System Watercooled manifold and turbocharger; dry elbow Flywheel and Flywheel Housing Fuel System Fuel priming pump, fuel transfer pump, fuel filter, flexible fuel lines Fuel pressure gauge, service meter, heavy-duty standard SAE rotation tachometer drive Lube System Top-mounted crankcase breather, oil filter, LH oil filler and oil level gauge, oil pan Mounting System Front support Vibration damper and guard. Caterpillar yellow paint, lifting eyes ACCESSORY EQUIPMENT_ Auxiliary Drive Pulley Digital Tachometer Double Wall Fuel Lines and Drain Duplex Fuel Filter Electric Overspeed Shutoff Electric Starting Motor Engine-Mounted Instrument Panel Exhaust Elbow, Pipe, Rain Cap, Flexible Fittings Front Enclosed Clutch Fuel Ratio Control Hydraulic Pump Drive Magnetic Pickup Manual Shutoff Lever Manual Sump Pump Pilot House Instrument Panel Primary Fuel Filter/Water Separator Remote-Mounted Pilot House Controls Remote Positive Locking Governor Control

PERFORMANCE CURVES Maximum Power - Prop Demand Performance Data Cubic prop demand curve with 3.0 exponent for displacement hulls only. Maximum Power - Prop Demand Performance Data Power produced at the flywheel will be within standard tolerances up to 50°C (122°F) combustion air temperature measured at the air cleaner inlet, and fuel temperature up to 52°C (125°F) measured at the fuel filter base. Power rated in accordance with NMMA procedure as crankshaft power. Reduce crankshaft power by 3% for propeller shaft power. 2001 Caterpillar All Rights Reserved

Right Side Overall Length Length from rear face of block to front of engine Length from rear face of block to back of flywheel housing Overall Height Height from crankshaft centerline to top of engine Height from crankshaft centerline to bottom of oil pan Overall Width Width from crankshaft centerline to port side (left side) Width from crankshaft centerline to starboard side (right side) Customer mounting hole diameter Width from crankshaft centerline to mounting holes Length from rear face of block to mounting holes •Illustrations and dimensions from drawing: 188-1628 RATING DEFINITIONS...

Performance data is calculated in accordance with tolerances and conditions stated in this specification sheet and is only intended for purposes of comparison with other manufacturers' engines. Actual engine performance may vary according to the particular application of the engine and operating conditions beyond Caterpillar's control. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. Supersedes LEHM7240-01 All rights reserved.

Shown with Accessory Equipment Engine Weight, Net Dry (approx) .. 1120.9 kg (2469 lb) STANDARD EQUIPMENT ACCESSORY EQUIPMENT Dry, regular duty air cleaner Cooling System Gear driven centrifugal jacket water pump, engine oil cooler, expansion tank, thermostats and housing, transmission oil cooler Exhaust System Watercooled manifold and turbocharger; dry elbow Flywheel and Flywheel Housing Fuel System Fuel priming pump, fuel transfer pump, fuel filter, flexible fuel lines Fuel pressure gauge, service meter, heavy-duty standard SAE rotation tachometer drive Lube System Top-mounted crankcase...

PERFORMANCE CURVES Maximum Power - Prop Demand Performance Data Cubic prop demand curve with 3.0 exponent for displacement hulls only. Maximum Power - Prop Demand Performance Data Power produced at the flywheel will be within standard tolerances up to 50°C (122°F) combustion air temperature measured at the air cleaner inlet, and fuel temperature up to 52°C (125°F) measured at the fuel filter base. Power rated in accordance with NMMA procedure as crankshaft power. Reduce crankshaft power by 3% for propeller shaft power. © 2001 Caterpillar All Rights Reserved

Right Side Overall Length Length from rear face of block to front of engine Length from rear face of block to back of flywheel housing Overall Height Height from crankshaft centerline to top of engine Height from crankshaft centerline to bottom of oil pan Overall Width Width from crankshaft centerline to port side (left side) Width from crankshaft centerline to starboard side (right side) Customer mounting hole diameter Width from crankshaft centerline to mounting holes Length from rear face of block to mounting holes •Illustrations and dimensions from drawing: 188-1628 RATING DEFINITIONS...

Performance data is calculated in accordance with tolerances and conditions stated in this specification sheet and is only intended for purposes of comparison with other manufacturers' engines. Actual engine performance may vary according to the particular application of the engine and operating conditions beyond Caterpillar's control. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication. Supersedes LEHM7240-01 All rights reserved.

Shown with Accessory Equipment Engine Weight, Net Dry (approx) .. 1120.9 kg (2469 lb) STANDARD EQUIPMENT ACCESSORY EQUIPMENT Dry, regular duty air cleaner Cooling System Gear driven centrifugal jacket water pump, engine oil cooler, expansion tank, thermostats and housing, transmission oil cooler Exhaust System Watercooled manifold and turbocharger; dry elbow Flywheel and Flywheel Housing Fuel System Fuel priming pump, fuel transfer pump, fuel filter, flexible fuel lines Fuel pressure gauge, service meter, heavy-duty standard SAE rotation tachometer drive Lube System Top-mounted crankcase...

PERFORMANCE CURVES Maximum Power - Prop Demand Performance Data Cubic prop demand curve with 3.0 exponent for displacement hulls only. Maximum Power - Prop Demand Performance Data Power produced at the flywheel will be within standard tolerances up to 50°C (122°F) combustion air temperature measured at the air cleaner inlet, and fuel temperature up to 52°C (125°F) measured at the fuel filter base. Power rated in accordance with NMMA procedure as crankshaft power. Reduce crankshaft power by 3% for propeller shaft power. © 2001 Caterpillar All Rights Reserved