C18 ACERT (1015, 1150 mhp) - Pleasure Craft

Product catalog summary

Engine Dimensions & Weight
- Length: 1931 mm (76.0 in)
- Width: 1204 mm (47.4 in)
- Height: 1198 mm (47.2 in)
- Net Dry Weight: 1814 kg (4,000 lb)
Note: These dimensions should not be used for installation design. Refer to general dimension drawings for details.

Specifications
- Engine Type: I-6, 4-stroke-Cycle-Diesel
- Compliance: EPA Tier 3 Recreational/IMO II
- Displacement: 18.0 L (1098 cu in)
- Rated Engine Speed: 2300 rpm
- Bore x Stroke: 145 mm (5.7 in) x 183 mm (7.2 in)
- Aspiration: Turbocharged and aftercooled
- Governance: Electronically governed
- Cooling: Heat exchanger cooled
- Refill Capacities:
- Cooling System: 45 L (12 gal)
- Lube Oil System: 49 L (13 gal)
- Oil Change Interval: 250 hours
- Recommended Oil: Caterpillar Diesel Engine Oil 10W30 or 15W40
- Flywheel: SAE No. 1 with 113 teeth (18 inch)
- Rotation: Counterclockwise from flywheel end

Standard Engine Equipment
- Corrosion-resistant sea water aftercooler
- Air cleaner/fumes disposal (closed system)
- Crankcase breather
- Titanium plate heat exchanger with integral fuel cooler
- Coolant recovery system
- Sea water pump and jacket water pump
- Aftercooler condensate drains (front and rear)
- Watercooled exhaust manifold and turbochargers
- Round flanged exhaust outlet
- Engine oil cooler and oil filler
- Center sump oil pan
- Oil filter and dipstick (RH or LH service)
- MEUI fuel system
- Fuel filter (RH or LH service)
- Fuel transfer and priming pumps
- Hybrid fuel lines
- Electronic fuel/air ratio control
- Adjustable mounting system
- SAE A hydraulic pump drive
- Two-groove crankshaft pulley
- Front damper guard
- Customer wiring and service tool connector

Performance Data
- Maximum Power:
- 1015 mhp (747 bkW) @ 2300 rpm
- 1150 mhp (847 bkW) @ 2300 rpm
- Prop Demand:
- Various power outputs and fuel consumption rates at different RPMs are provided, indicating efficiency and performance metrics.

Optional Equipment
- Sea water pump with vertical inlet
- Battery charger (10 amp)
- Charging alternator (24V 105 amp)
- Primary fuel/water separator
- Primary fuel filter
- Fuel cooler and flexible fuel lines
- Transmission oil cooler
- Electric starting motor (24V LH service)
- Battery sets (24V 950-1300 CCA)
- MECP I control panel
- OEM wiring harness (30, 50, 80 foot lengths)
- Engine-to-engine wiring harness (15, 30 foot lengths)
- Transmission sensors (pressure, temperature)
- Five-groove pulley stack (8-inch diameter)

Catalog excerpts

C18 ACERT (1015, 1150 mhp) - Pleasure Craft-1

PRELIMINARY standard ENGINE equipment MARINE PROPULSION engine 1015 mhp 1150 mhp Image shown may not reflect actual engine Corrosion-resistant sea water aftercooler Air cleaner/fumes disposal (closed system) Crankcase breather Titanium plate heat exchanger with integral fuel cooler Coolant recovery system Sea water pump and jacket water pump Front- and rear-down aftercooler condensate drains Watercooled exhaust manifold and turbochargers Round flanged exhaust outlet Engine oil cooler and oil filler Center sump oil pan Oil filter and dipstick, RH or LH service MEUI fuel system Fuel filter RH or LH service Fuel transfer and priming pumps Hybrid fuel lines Electronic fuel/air ratio control Front support adjustable mounting system SAE A hydraulic pump drive Two-groove crankshaft pulley Front damper guard Customer wiring and service tool connector Right Side • EPA Tier 3 Recreational/IMO II compliant • 18.0 L (1098 cu in) displacement • 2300 rpm rated engine speed • 145 mm (5.7 in) bore x 183 mm (7.2 in) stroke • Turbocharged and aftercooled aspiration • Electronically governed • Heat exchanger cooled • Refill capacity – Cooling system: 45 L (12 gal) – Lube oil system: 49 L (13 gal) • 250-hour oil change interval • Caterpillar Diesel Engine Oil 10W30 or 15W40 • AE No. 1 flywheel and flywheel housing, S 113 flywheel teeth (18 inch) • ounterclockwise rotation from flywheel end C Note: Do not use these dimensions for installation design. See general dimension drawings for detail.

Open the catalog to page 1

C18 ACERT (1015, 1150 mhp) - Pleasure Craft-2

MARINE PROPULSION engine MARINE ENGINE PERFORMANCE — PRELIMINARY Prop Demand Maximum Power Torque lb-ft Torque lb-ft Prop Demand OPTIONAL EQUIPMENT • • • • • • • • Sea water pump – vertical inlet Battery charger 10 amp Charging alternator 24V 105 amp Primary fuel/water separator Primary fuel filter Fuel cooler, flexible fuel lines Transmission oil cooler Electric starting motor – 24V LH service • Battery sets – 24V 950-1300 CCA • MECP I control panel • OEM wiring harness – 30,50,80 foot lengths • ngine-to-engine wiring harness – 15, 30 foot E lengths • Transmission sensors – pressure, temperature...

Open the catalog to page 2