HR-Series Sealed Rocker Switches PROD UC T W E BP A GE request sample, configure part, watch video Perimeter Illuminated Low Profile Actuator The HR-Series comes with a variety of dependent and independent illumination options; momentary and maintained circuits; and up to two customizable laseretched legends. The patented design supports the various illumination options and allows the switch to be rated up to 20 amps, eliminating the need for relays. Typical Applications ∙ Marine ∙ Outdoor Construction Signage ∙ Any Application Requiring Sealing Protection

Design Features 20A 12VDC RATING Robust construction to handle a multitude of electrical loads. SNAP-IN MOUNTING Fits into an industry standard mounting hole of 1.450 x .830 in. (Same as V-Series and W-Series) With dedicated TE connector for ease of installation. Sold Separately. (See General Specs for TE Part Numbers) PERIMETER ILLUMINATION Choice of independent (full) or dependent (half) lighting, in a variety of colors. MAINTAINED/ MOMENTARY Circuits available in 2 or 3 positions. IP68 ABOVE PANEL SEALING Seals out dust and moisture. LASER ETCHED LEGENDS Rocker icons convey a clean, sleek...

Tech Specs Electrical Operating Voltage Designed for 12 Volt systems 9-16 VDC operating Contact Rating Supply Voltage Ratings Environmental Sealing IP68, for above-panel components of actual switch only. Operating Temperature The switch passes the following supply voltage testing: SAE J1455 section 4.13.1 for power-up, operating voltage, over voltage, reverse polarity, and short circuit -40°C to 85°C The following codes were passed: Cold Soak (IEC 60068-2-1) Heat Soak (IEC 60068-2-2) Cycling/Shock (IEC 60068-2-14) General: IEC 60068-2-6, Swept sine wave section 8.2, 5 - 500 Hz 20 cycles 10g acceleration...

Ordering Scheme Sample Part Number Selection Rocker Illumination: 2 and 3 Position Switches A1 Independent LED 1: 10(+) 1(-) LED 2: 2(+) 1(-) A2 Independent LED 1: 10(+) 1(-) No Illumination A3 No Illumination 2 Position Switch A4 Dependent A5 Dependent A6 Dependent 3 Position Switch A7 Dependent HALF PERIMETER ILLUMINATION Rocker Illumination: LED 1 and 2: 10(+) 1(-) Perimeter Illumination: 3 Position Switch Position 1 B1 Dependent Top Half On 10(+) 2(+) 1(-) Painted Black Painted Silver Painted Black Painted Silver Laser Etched Position 2 Position 3 Full Illumination Bottom Half On 10(+) 1(-)...

Illumination Options (Perimeter and Legend) Independent Illumination: 2 Position Switch Position 1 Dependent Illumination: 2 Position Switch Position 1 3 Position Switch Position 1 A6 LEGEND: Used for illumination representation only. Refer to legend code page for complete list if standard legends.

Dimensional Specs inches [millimeters] MATES WITH TE CONNECTOR 14 18994 -1 *Manufacturer reserves the right to change product specification without prior notice. PANEL CUTOUT

Circuit Diagrams Circuit Code CIRCUIT DIAGRAM Circuit Code Notes: 1. Recommended minimum load per circuit is 1 milliamp *Manufacturer reserves the right to change product specification without prior notice.

Illumination Circuit Diagrams ILLUMINATION CIRCUIT DIAGRAM Illumination Code ILLUMINATION CIRCUIT DIAGRAM Illumination Code *Manufacturer reserves the right to change product specification without prior notice.

Standard Legend Codes YK WATER PUMP ISO compliant symbols. Consult factory for custom legends.

Authorized Sales Representatives and Distributors Click on a region of the map below to find your local representatives and distributors or visit www.carlingtech.com/findarep. MIDDLE EAST ASIA-PACIFIC OCEANIA SOUTH AMERICA About Carling Founded in 1920, Carling Technologies is a leading manufacturer of electrical and electronic switches and assemblies, circuit breakers, electronic controls, power distribution units, and multiplexed power distribution systems. With six ISO9001 and IATF16949 registered manufacturing facilities and technical sales offices worldwide, Carling Technologies Sales, Service...