Catalog
44Pages

boathandling systems : Sweden

SBS/MBS Galvanized boat stand SBS Top of Marine plywood for higher strength. Rod and adjustment nut in solid steel. Hot dipped. Hot dipped. Steinless screws with locking nut. Rod and adjustment nut in solid steel. Hot dipped. Rod and adjustment nut in solid steel. Hot dipped. Stackable, adapted similar products on the market.

• The number of stands is determined by weight, weight distribution and length of the boat. • Use a wide, large sized block as keel support both in the front and back of the keel. • An extra pair of stands should be used on a boat with the rig raised. • Select type of stand to enshure equal adjustment for the Acme thread in both directions. • Type of stand is determined by: Draft + height of keel support - approximately 0,25 m = height of stand. 1. Large top/Orange 2. Medium top/Grey Rod 27" Rod 23"

• The type of stand is determined by keel support and shape of the hull. MBS is used for flat bottom. SBS is to be used for all other hull shapes (eg for the bow or sharp V-shaped hulls). • The number of stands is determined by weight, weight distribution and length of the boat. • Use KS3, KS4 or large sized blocks as keel support. • Select type of stand to enshure equal adjustment for the Acme thread in both directions. 1. Large top/Orange 2. Medium top/Grey 3. Small top/Blue 4. Not stackable Rod 27“ Rod 23“ Rod 16“

User guide •B oat stands should only be used on firm surface where surrunding conditions (like weather) never affect the stability. • osition the stands according to the boat manufactuers recomendations, normaly a pair of P stands for every 2,6–3,3 meter (8–10 feet). • he entire weight of the boat should be borne by the keel support, not by the stands. T • he keel support should be placed depending on the weight distribution of the boat. T • afety chain should always be used to secure the stands to each other. S • Never tie anything to the stands (like cover). In heavy wind the stands might...

En stålvagga för alla kölbåtar upp till 18 meters längd, tillverkas i ett flertal varianter för att passa varje båttyp. An all-steel cradle suitable for keelboats of max 18 meter length overall. A variety • Mycket stor stabilitet of models are available to fit every kind of boat type. • Väl dimensionerad bottenram med kraftig kölstege garanterar säker stöttning • Outstanding stability • Enkelt demonterbar vid förvaring och transport • A carefully dimensioned bottom frame, equipped with • Teleskopiska stöttor med a reliable shoring up a strong keel ladder, guarantees finjustering och...

BOATHANDLING SYSTEMS SteelCradle/ BOATHANDLING SYSTEMS Type Typ I I Typ I Förlängningssats ningssats I/II III/II Stöttor Stands Stöttor (antal) (No. of) (antal) 44 Bredd (a) Längd (b) Höjd stötta (c) Vikt Width (a) Längd (m) Length (b) Stand height Weight Bredd (m) (a) (b) Höjd stötta m) (c) Vikt kg) (ca (c) (ca (m) (m) (approx (approx. kg) (m) (m) (ca m) m) (ca kg) 2,5 150 2,5 150 150 2,5 2,2 3,0 0,9-1,4 /1,1-1,6 165 2,2 3,0 0,9-1,4 /1,1-1,6 165 165 2,2 3,0 4,0 180 4,0 180 4,0 180 0,9–1,4/1,1–1,6 3,0 180 2,2 1,4-1,9 3,0 180 4,0 200 2,2 1,4-1,9 4,0 200 60 2,2 +1,35 2,2 Type I, II and IV can...

Type I, II and IV can be delivered in width 2,60 m.

Recommendations: The length of the cradle should be approximately 1/3 of the length of the boat. Motorsailers may need stanchions with specially adapted height. For extra stability for boats with heavy stern/aft, use the extension kit (maximum 2 per cradle). If in doubt - consult the manufacturer.

SteelCradle/ TYBEStiWkfiGAN Type

Recommendations: The length of the cradle should be approximately 1/3 of the length of the boat. Motorsailers may need stanchions with specially adapted height. For extra stability for boats with heavy stern/aft, use the extension kit (maximum 2 per cradle). If in doubt - consult the manufacturer.

En stålbock som passar de allra flesta motorbåtar, tillverkas i olika typer för att klara laster på 500 - 10 000 kg per bock. An all-steel bar stand suitable for almost all kinds of motorboats. A variety of models are available to carry loads ofrelativt sin egen each. • Klarar hög last 500–10.000 kg vikt • Stabil konstruktion • arry heavy load compared to the weight of the C • Enkelt demonterbar vid förvaring och transport bar stand itself • Teleskopiska stöttor med finjustering • Designed for high stability • Kulledad skrovplatta (skrovskydd av gummi som extra for storage to transportation...

General recommendations: The choice of bar stand size should be based on the total weight of the boat and distribution. Be sure to find out where the engine is placed. Boats with AQ installations are always stern-heavy. For single engine installations the weight distribution should be approximately 30/70 (stem/stern) as a rough estimation. Outboard motorboats tend to have a slightly better weight distribution since the motor is not usually as heavy as a corresponding AQ. Note! The weight of the boat must include fuel, (water), supplementary equipment etc. generally specify the weight of an...

An all-steel alla suitable for till 18 meters längd, length overall. A variety En stålstötta förstand båtar upp boats of max 18 metertillverkas i ett flertal varianter för of models are available to fit every kind of och att passa varje båttyp. Avsedd för klubbar boat. varv/marinor med bra markförhål  The steel stand is intended for clubs, marinas and boatyards at locations with landen som ej kräver den garanterade säkerhet som ger med sin good ground conditions, where the outstanding safety of the G-C SteelCradle mycket stabila bottenram/kölstege-design. with its very stable bottom frame...