Catalogs >
Awlgrip >
Max Cor CF Primer

Max Cor CF Primer
2Pages

Catalog excerpts

Product Data Sheet Max Cor CF Intended Uses Max Cor CF is a high solids two component anti-corrosive, chromate-free epoxy primer for aluminum and steel with excellent chemical and solvent resistance. Max Cor CF is based on 'Controlled Fusion' (CF) technology, a unique chemical system that allows extended re-coat times, removes the need for sanding prior to applying the next coat and also gives excellent substrate adhesion. The technology eliminates the requirement for high hazard chemicals and ensures a tightly fused intercoat layer between the CF-based coating and the next applied coat. For above the waterline only. Specification Data Volume Solids Specific Gravity Available Packs 56% 1.20 Base available in a 1 gallon pack, converter in a ½ gallon pack. Typical Shelf Life - 2 years OR4330 OR3330 Do not thin/reduce T0006, T0176 (NA only), Acetone or M.E.K. Base Converter Reducer Equipment Cleaning Theoretical Coverage Application Methods Theoretical Coverage Per Coat (at recommended DFT) Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size and application environment. VOC All VOC information contained herein is theoretical (unless otherwise stated). Actual VOC content may vary by batch and when tested via standard test methodology. Product As Supplied (without reducer) g/L Surface Preparation The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation. Max Cor CF may be directly applied to grit blasted steel in accordance with SSPCSP10 to a 23 mil (5070 microns) profile (or Sa2½ outside of the US). Alternatively power grind with 16 to 36 grit disc to obtain profile. The surface must be clean and dry, free of all dirt, grease and oil. Use Awlgrip Wipe-Down Solvent (NA: Awlprep T0008 or Awlprep Plus T0115; AP: Awlprep Plus T0115; EU: Surface Cleaner T0340). Aluminium: Sandblasted/ground to 100% clean silver color. A surface profile of 2-3 mils (50-75 microns) is recommended. Steel: Sandblast/grind SSPCSP10 or Sa2½. A surface profile of 23 mils (5075 microns) is recommended. Mixing & Reduction Application Methods Air Atomized Recommended Thinning Spraying Viscosity Mix by volume 2 parts OR4330 with 1 part OR3330. Ensure OR4330 is uniformly dispersed before addition of OR3330. Mix until a smooth homogenous mixture is obtained. Anticipated Pot Life at 77°F (25°C) @ 50% R.H: 2 hours Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. Application Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary. Spray only. Apply one smooth wet coat. Substrate may be visible through dry film. Do not exceed maximum recommended dry film thickness. Do not apply paint materials to surfaces warmer than 40°C/105°F or colder than 15°C/59°F. Do not attempt to cure products at temperatures below 15°C/59°F. IMPORTANT NOTES: Read Material Safety Data Sheet before using. Methods FluidforTip Please refer to yourApplication local representative or visit http://www.awlgrip.com further information. Fluid Pressure Air Atomized 0.85 - 1.10 mm Awlgrip, the AkzoNobel logo and other products mentioned in this publication are trademarks of AkzoNobel.- ©AkzoNobel 2019 33 - 43 thou 1 of 2 Ref:10404 Max Cor CF Recoatability & Drying Times Fluid Flow Rate

Open the catalog to page 1

Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. ProductApplication Data Sheet Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further Max Cor CF advice if...

Open the catalog to page 2