PRODUCT DATA SHEET HULLGARD EXTRA EPOXY PRIMER D6120/D3730 Page 1 of 2 Features & Uses HULLGARD EXTRA Primer is a two component epoxy substrate primer with excellent anticorrosive properties. It offers excellent aged recoatability and provides a perfect base for subsequent fairing with Awlfair fairing compound(s). Specification Data Type: Two component epoxy Color: White Packaging: All countries: Available in 1 Gallon base (0.87GL fill volume) and 1 Quart converter (16.7 fl.oz fill volume). Mixed volume is 1 Gallon. EU only: Available in 5 Gallon base (16.45lt fill volume) and 84fl.oz converter (2.46lt fill volume). Mixed volume is 5 Gallon. Also available in 1 Quart Kit pack where mixed volume is 1 Quart. 2 Theoretical Coverage - 185 Sq. feet/gallon = 4.6m / litre at 4 mils/ 100 microns DFT. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 9 mils (225 microns) per coat by airless spray, 5 mils (125 microns) per coat by brush/roller Recommended Dry Film Thickness: 4 mils (100 microns) per coat by airless spray, 2.5 mils (60 microns) per coat by brush/roller Number of coats: 1 by airless spray (at 4 mils/100 microns DFT). Anticipated Drying Time at 77°F/50% R.H: 30 minutes dust-free, 6 hours touch dry; 10 hours hard dry. Recoatability (At 77°F/25°C, 50% RH): With Itself or: Primers/surfacers 2 hours (minimum) Maximum recoat time, without sanding 6 months (in shed). Inspection for cleanliness is recommended. Do not wipe with solvents With Fillers: 16 hours (minimum) Maximum recoat time, without sanding 6 months (in shed). Inspection for cleanliness is recommended. Do not wipe with solvents Base (D6120) – 482 g/lt or 4.0 lbs/gallon Converter (D3730) – 376 g/lt or 3.1 lbs/gallon Mixed components, unreduced (as supplied) VOC is 468 g/lt or 3.9 lbs/gallon Application Equipment Apply by airless spray, air atomized spray, brush or roller. Airless spray is the most efficient way to apply this product 2270 Morris Avenue • Union, New Jersey 07083 • USA • Tel: 888.355.3090 • Fax: 908.686.1752 Bannerlaan 54 • B-2280 Grobbendonk • Belgium • Intl. Tel: 32.14.257770 • Intl. Fax: 32.14.230880 76 Waterway Drive • Coomera • QLD 4209 • Australia • Tel: 61.7.5573.9655 or 1800.007.866 • Fax: 61.7.5573.9677 686 Rosebank Road • Avondale • Auckland • New Zealand • Tel: 64.9.828.3009 or 0800.150.527 • Fax: 64.9.828.1129 No. 1 Tuas Avenue 4 • Singapore 639382 • Tel: 65.6862.2928 • Fax: 65.6862.0778 Page 1 of 2 • Rev 7 – JULY 2011 HULLGARD EXTRA EPOXY PRIMER

PRODUCT DATA SHEET HULLGARD EXTRA EPOXY PRIMER D6120/D3730 Page 2 of 2 Airless Equipment Graco or Binks equivalent: Orifice Size………….019” – .021” size) Fan size & Angle…..8” – 80°, or 6” – 60° On a 25-1 pump, the input pressure gauge should read 70 to 80 lbs. On a 40-1 pump, the input pressure gauge should read 50 to 60 lbs. Spray gun………..#95 Fluid nozzle……..#68SS (.110” Orifice Fluid needle……..#668 Air nozzle………..#68PB Pressure gauge should read 15-25 lbs. Atomizing pressure 50+ lbs. Surface Preparation Hullgard Extra may be directly applied to grit blasted steel in accordance with SSPC-SP10...