PRODUCT DATA SHEET (EU ONLY) HULLGARD EPOXY PRIMER D6070/D3707 Features & Uses Hullgard Epoxy Primer is a two component epoxy primer that combines excellent anticorrosion and water barrier properties with anti-fouling tie-coat functionality. It offers a long overcoating interval without sanding to reduce work time for underwater systems. Specification Data Type: Two component epoxy Color: Buff Packaging: Available in a 1 Gallon container (base, filled to ¾ GL) and 1 Quart (converter, filled to 1QT). Mixed volume 1 US Gallon. 2 Theoretical Coverage – 140 Sq. feet/gallon = 3.5 m /litre at 5.5 mils/135 microns DFT or 360 Sq. feet/ gallon (9m²/lt) at 2 mils/ 50 microns DFT. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 12 mils (300 microns) per coat by spray, 4 mils (100 microns) per coat by brush/roller. Recommended Dry Film Thickness: 5.5 mils (138 microns) per coat by spray, 2 mils (50 microns) per coat by brush/roller. Number of coats: See application instructions Anticipated drying time at 77° F/25° 2 hours touch dry; 7 hours hard dry. C: Recoatability (At 77° 25° 50% RH): F/ C, With Itself: 2 hours (minimum) Maximum recoat time without sanding 6 months. Inspection for cleanliness recommended prior to subsequent application. Ensure dust is removed and remove any dirt pick-up with T0006. If recoatability time is exceeded abrade using 180 – 220 grit paper. With Antifouling: Minimum 2 hours by brush/roller or 6 hours by spray at recommended film thickness. Maximum recoat time 7 hours by brush/roller or 16 hours by spray at recommended film thickness. VOC: Base (D6070) – 391g/lt or 3.26 lbs/gallon Converter (D3707) – 634 g/lt or 5.29 lbs/gallon Application Equipment Apply by airless spray, air atomized spray, brush or roller. Airless spray is the most efficient way to apply this product 2270 Morris Avenue • Union, New Jersey 07083 • USA • Tel: 908.686.1300 • Fax: 908.964.2219 Bannerlaan 54 • B-2280 Grobbendonk • Belgium • Intl. Tel: 32.14.257770 • Intl. Fax: 32.14.230880 76 Waterway Drive • Coomera • QLD 4209 • Australia • Tel: 61.7.5573.9655 or 1800.007.866 • Fax: 61.7.5573.9677 686 Rosebank Road • Avondale • Auckland • New Zealand • Tel: 64.9.828.3009 or 0800.150.527 • Fax: 64.9.828.1129 No.1 Tuas Avenue 4 • Singapore 639382 • Tel: 65.6862.2928 • Fax: 65.6862.0778 Page 1 of 2 • Rev 8 – APRIL 2013 • HULLGARD EPOXY PRIMER (EU ONLY)

PRODUCT DATA SHEET (EU ONLY) HULLGARD EPOXY PRIMER D6070/D3707 Airless Equipment Graco or Binks equivalent: : Orifice Size………….028” – .043” Fan size & Angle…..8” – 80° or 6” – 60° , On a 25-1 pump, the input pressure gauge should read 70 to 80 lbs. On a 40-1 pump, the input pressure gauge should read 50 to 60 lbs. Spray gun………..#95 Fluid nozzle……..#68SS (.110” Orifice size) Fluid needle……..#668 Air nozzle………..#68PB Pressure gauge should read 15-25 lbs. Atomizing pressure 50+ lbs. Surface Preparation Hullgard Epoxy Primer may be directly applied to grit blasted steel in accordance with SSPC-SP10...