PRODUCT DATA SHEET Flat Black Awlgrip® Topcoat G2002 Features & Uses A two component, polyester based, light-fast, linear aliphatic polyurethane coating in a flat finish, with outstanding chemical resistance and color retention. Do not wax, buff, compound, or polish. For use above the waterline only. Not recommended for application to large expanses of surface as unequal gloss and appearance may result. Specification Data Type Color Packaging Two Component Linear Aliphatic Polyester Polyurethane Black Available in 1 gallon and 1 quart containers. Spray Application: 415 Sq. Feet (39 m ) at 1 mil (25 microns) dry film thickness; 180 Sq. Feet (17 m ) at recommended dry film thickness. Recommended Wet Film Thickness 6-9* mils (150-225 microns), total of 3 or more coats. Recommended Dry Film Thickness 2-3 mils (50-75 microns), total of 3 or more coats. * increasing wet film thicknesses on the final coat will increase the final gloss, conversely a lower film thickness will reduce the gloss. Coverage calculations are based on a theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Anticipated Cure Time at 77°F/25°C, 50% R.H: 24 hours to tape free; 3 to 4 days to light service; 14 to 21 days for full cure. Recoatability (at 77°F/25°C, 50% RH): Spray applications consist of three coats applied over 1-4 hours. Exact time will vary with temperature, project size, and film thickness applied. Awlgrip topcoats which have been allowed to cure more than 24 hours must be sanded before recoating. VOC: Base (G2002) – 557 g/lt or 4.6 lbs/gallon Converter (G3010) – 591 g/lt or 4.9 lbs/gallon Product Components, Reducers, Additives and Auxiliary Components AWLGRIP Flat Black Base AWLCAT #2 Spray Converter Spray Reducer PRO-CURE Accelerator X-98 PRO-CURE Accelerator X-138 GRIPTEX Non-Skid Particles-Fine GRIPTEX Non-Skid Particles-Coarse CRATER-X Equipment Cleaning Application Equipment Conventional air atomized spray or HVLP spray. 1 East Water Street • Waukegan, Illinois 60085 • USA • Tel: 847.599.6212 • Fax: 847.599.6209 Bannerlaan 54 • B-2280 Grobbendonk • Belgium • Intl. Tel: 32.14.257770 • Intl. Fax: 32.14.230880 76 Waterway Drive • Coomera • QLD 4209 • Australia • Tel: 61.7.5573.9655 or 1800.007.866 • Fax: 61.7.5573.9677 686 Rosebank Road • Avondale • Auckland • New Zealand • Tel: 64.9.828.3009 or 0800.150.527 • Fax: 64.9.828.1129 No.1 Tuas Avenue 4 • Singapore 639382 • Tel: 65.6862.2928 • Fax: 65.6862.0778 Page 1 of 2 • Rev 9 – February 2012 • FLAT BLACK AWLGRIP® TOPCOAT

PRODUCT DATA SHEET Flat Black Awlgrip® Topcoat G2002 SPRAY EQUIPMENT: Pressure Pot System: Devilbiss or equivalent: Spray Gun: JGA type Fluid Nozzle: AV-645-FX Fluid Needle Size: 1.1 Air Nozzle: AV-4239-43 Fluid Flow Rate: 170 – 270 ml/min GUN PSI: 2.5 – 3.5 bar (36-51 psi) Cup Gun System: Devilbiss or equivalent: Spray Gun: JGA type Fluid Nozzle: AV-4239-43 Fluid Needle Size: 1.1 Air Nozzle: AV-4239-43 GUN PSI: 2.0 – 3.0 bar (29-44 psi) Surface Preparation Awlgrip G2002 Flat Black should be applied over properly prepared 545 Epoxy Primer or 321 HS Undercoat. Mixing & Reduction Spray: Mix by...