Catalogs >
Awlgrip >
Awlquik Epoxy Primer/Surfacer D8003/D9001

Awlquik Epoxy Primer/Surfacer D8003/D9001
2Pages

Catalog excerpts

Awlquik Epoxy Primer/Surfacer D8003/D9001 - 1

PRODUCT DATA SHEET Awlquik Epoxy Primer/Surfacer D8003/D9001 Features & Uses A quick drying, medium build, easily sanded, two component epoxy primer/surfacer. Easy to apply by brush, roller or spray. Not to be used below the waterline. Specification Data Type: Epoxy Polyamide Packaging: Available in 1 gallon and 1 quart containers 2 Theoretical Coverage: Sq. Feet/Gallon: 609 Sq. Feet (57m ) at one mil dry (25 microns). 2 203-305 Sq. Feet (19-28m ) at recommended dry film thickness. Calculated for mixed base and converter reduced 50%. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 5 mils (125 microns) Recommended Dry Film Thickness: 2-3 mils (50-75 microns) Recoatability: At 77F/50% R.H. Spray: may be overcoated with itself, 4 hours; with 545 Primer or topcoat, 12 hours. Brush Roll: with itself, 12 - 14 hours, with other products 12 - 14 hours. Maximum without sanding: 24 Hours. May be overcoated with Awlgrip/Awlcraft 2000 Topcoats, and 545 Epoxy Primer. Note: Sealing Awlquik with 545 Primer before applying an Awlgrip/Awlcraft 2000 topcoat will maximize gloss and D.O.I. of the topcoat. VOC: Base (D8003) – 436 g/lt or 3.6 lbs/gallon Converter (D9001) – 354 g/lt or 3 lbs/gallon Product Components, Reducers, Additives, and Auxiliary Components Application Equipment Conventional or airless spray and brush/roller. Airless Equipment Graco or Binks equivalent: Orifice Size………….028” – .043” Fan size & Angle…..8” – 80° or 6” – 60° , On a 25-1 pump, the input pressure gauge should read 70 to 80 lbs. On a 40-1 pump, the input pressure gauge should read 50 to 60 lbs. Pressure Pot Spray gun………..#95 Fluid nozzle……..#63BSS (.046” Orifice size) Fluid needle……..#663A Air nozzle………..#63PW Pressure gauge should read 8-12 lbs. Atomizing pressure 50 to 60 lbs. 2270 Morris Avenue • Union, New Jersey 07083 • USA • Tel: 908.686.1300 • Fax: 908.964.2219 Bannerlaan 54 • B-2280 Grobbendonk • Belgium • Intl. Tel: 32.14.257770 • Intl. Fax: 32.14.230880 76 Waterway Drive • Coomera • QLD 4209 • Australia • Tel: 61.7.5573.9655 or 1800.007.866 • Fax: 61.7.5573.9677 686 Rosebank Road • Avondale • Auckland • New Zealand • Tel: 64.9.828.3009 or 0800.150.527 • Fax: 64.9.828.1129 No.1 Tuas Avenue 4 • Singapore 639382 • Tel: 65.6862.2928 • Fax: 65.6862.0778 Page 1 of 2 • Rev 4 – SEPTEMBER 2010 • AWLQUIK EPOXY PRIMER/SURFACER

Open the catalog to page 1

Awlquik Epoxy Primer/Surfacer D8003/D9001 - 2

PRODUCT DATA SHEET Awlquik Epoxy Primer/Surfacer D8003/D9001 Surface Preparation Best when used as a surfacer over other Awlgrip Primers. May be applied by brush or roller directly to properly prepared wood or fiberglass. Best results are obtained when these surfaces are first sealed with 545 Primer. Mixing and Reduction Spray: Mix by volume 1 part D8003 Base with 1 part D9001 until a smooth, homogenous mixture is obtained. Reduce as necessary up to 50% with Spray Reducer T0006 Example: 8 oz. D8003, 8 oz. D9001, 8 oz. T0006. Brush/Roll: Reduce mixed D8003/D9001 as needed up to 50% with...

Open the catalog to page 2