PRODUCT DATA SHEET AWLGRIP® Topcoats G/H Line (Code Numbers can be found on Suggested List Price Schedule or Color Card) Features & Uses A two component, polyester based, light-fast, linear aliphatic polyurethane coating with long lasting gloss and color retention, and outstanding chemical resistance. Do not use below the waterline. A low maintenance coating. Do not wax, buff, compound, or polish. Specification Data Type: Two Component Linear Aliphatic Polyester Polyurethane Color: See Color Card and / or your Awlmix distributor. Packaging: Available in 1 gallon and 1 quart containers. Theoretical Coverage - Sq. Feet/Gallon Spray Application: 530 Sq. Feet (49m2) at 1 mil (25 microns) dry film thickness; 210 Sq. Feet (19.5m2) at recommended dry film thickness. Recommended Wet Film Thickness: 6-9 mils (150-225 microns), total of 3 or more coats. Recommended Dry Film Thickness: 2-3 mils (50-75 microns), total of 3 or more coats. Coverage calculations are calculated for mixed base and converter, reduced 25% and are based on a theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and environment. Brush/Roller Application: 700-725 Sq. Feet (65-67m2) at 1 mil (25 microns) dry; 285 Sq. Feet (26m 2) at recommended dry film thickness. Recommended Wet Film Thickness: 4-5 mils (100-125 microns), total of 2 or more coats. Recommended Dry Film Thickness: 2.0-2.5 mils (50-63 microns), total of 2 or more coats. Anticipated Cure Time at 77°F/50% R.H: 24 hours to tape free; 3 days to light service; 14 days for full cure. Recoatability: Spray applications consist of three or more coats applied over 1-4 hours. Exact time will vary with temperature, project size, and film thickness applied. Brush/Roller applications require at least 2 coats applied a minimum of 16 hours apart. AWLGRIP® topcoats which have been allowed to cure more than 24 hours must be sanded before recoating. VOC: Base: 470 g/lt or 3.9 lbs/gallon Spray Converter (G3010) 591g/lt or 4.9 lbs/gallon Brush Converter (H3002) 276 g/lt or 2.3 lbs/gallon Page 1 of 3 • Rev 8 – Aug 2014 • Awlgrip Topcoats G/H Line

PRODUCT DATA SHEET AWLGRIP® Topcoats G/H Line (Code Numbers can be found on Suggested List Price Schedule or Color Card) Application Equipment Conventional air atomized spray, HVLP spray, brush or roller. SPRAY EQUIPMENT: Pressure Pot System: Devilbiss or equivalent: Spray Gun: JGA type Fluid Nozzle: AV-645-FX Fluid Needle Size: 1.1 Fluid Flow Rate: 170 - 270 ml/min Air Nozzle: AV-4239-43 Gun PSI: 2.5 – 3.5 bar (36-51 psi) Cup Gun System: Devilbiss or equivalent: Spray Gun: JGA type Fluid Nozzle: AV-4239-43 Fluid Needle Size: 1.1 Air Nozzle: AV-4239-43 GUN PSI: 2.0 – 3.0 bar (29-44 psi) Surface...

PRODUCT DATA SHEET AWLGRIP® Topcoats G/H Line (Code Numbers can be found on Suggested List Price Schedule or Color Card) On large surfaces such as hull sides, transoms, and house sides, first roll the Awlgrip Topcoat and then smooth the roller stipple by lightly tipping the surface with a brush. This can be done with 2 painters working side by side (i.e., 1 rolling and 1 tipping), or with 1 painter rolling approximately 6 square feet and then tipping that area before rolling any further. Warning: Do not apply paint materials to surfaces less than 5°F (3°C) above dew point, or to surfaces warmer...