Catalogs >
Awlgrip >
Awlgrip HDT Clearcoat

Awlgrip HDT Clearcoat
2Pages

Catalog excerpts

Product Data earcoat Intended Uses Awlgrip HDT Clearcoat is a revolutionary high gloss topcoat which is VOC compliant (VOC-420g/L). Awlgrip HDT Clearcoat gives a hard finish which can be repaired and polished. Awlgrip HDT Clearcoat is designed to work as the final layer of a multi-part system using Awlcraft SE Basecoat. Awlcraft SE Basecoat imparts the colour and effect and is then topcoated with Awlgrip HDT Clearcoat to give gloss and protection. This combination forms a high performance, high gloss robust topcoat system. Specification Data Volume Solids Specific Gravity Available Packs Base Converter Reducer Equipment Cleaning Typical Shelf Life 49% (mixed product) 0.98 - Base 1 US Gallon (=3.78L) for Base and Curing Solution 1 US Quart (=0.95L) for Activators Awlgrip HDT Clearcoat (OC0300) Awlgrip HDT Curing Solution (OC0010) Activators: Awlgrip Slow Activator (OA0010) Awlgrip Fast Activator (OA0020) Activators are essential for the technology of this product to achieve the required curing. T0001, T0002, T0003 2 years for Base and Activators 1 year for Curing Solution Theoretical Coverage Coverage calculations are calculated for mixed base, curing solution and activators and are based on a theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size and application environment. The total DFT can be reached in 2 to 3 coats depending on application. Minimum DFT figures are post sanding. All VOC information contained herein is theoretical (unless otherwise stated). Actual VOC content may vary by batch and when tested via standard test methodology. VOC values are for the mixed product and recommended mixed ratio. Surface Preparation For the application of the basecoat please refer to the Awlcraft SE TDS. Awlcraft HDT Clearcoat should be applied over Awlcraft SE Basecoat or previous Awlgrip/Awlgrip HDT/Awlcraft Topcoat. Over basecoat ensure the surface must be clean and dry. Wipe with surface cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method. Over Awlgrip Topcoat/Awlgrip HDT/Awlcraft 2000 topcoat sand topcoat with P400 to remove the gloss and clean with surface cleaner T0170 (US) or T0340 (EU) using the two cloth wipe down method. Do not use unless mixed thoroughly with the curing agent at specified ratio. Avoid painting in direct sunlight. Substrate temperature should be minimum 5°C/41°F and maximum 30°C/86°F. Product temperature should be minimum 15°C/59°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 30°C/86°F. Avoid applying late in the evening as condensation can cause a loss of gloss during overnight cure. Allow to dry in a well ventilated environment. The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation. Mixing & Reduction Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. Mix Ratio (by volume): 1:1:0.25 (Base:Curing Solution:Activator) Induction time = 15 minutes. Mix to a smooth, homogenous mixture. Awlgrip HDT Clearcoat is designed for spray application only. Correct choice of activator must be made according to the application conditions and project Awlgrip, the AkzoNobel logo and other products mentioned in this publication are trademarks of AkzoNobel. ©AkzoNobel 2017

Open the catalog to page 1

Mixing & Reduction Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. Product Data Sheet Mix Ratio (by volume): 1:1:0.25 (Base:Curing Solution:Activator) Awlgrip HDT = 15 minutes. Clearcoat Induction time Mix to a smooth, homogenous mixture. Awlgrip HDT Clearcoat is designed for spray application only. Correct choice of activator must be made according to the application conditions and project size. General guideline:...

Open the catalog to page 2