Catalogs >
Awlgrip >
Awlfair Pumpable

Awlfair Pumpable
2Pages

Catalog excerpts

Product Data Sheet Awlfair Pumpable Intended Uses Awlfair Pumpable is designed for fairing, leveling or smoothing surface imperfections due to gouges, pitting, dents or weld seams. Awlfair Pumpable can be used above and below the waterline. Although designed as a cosmetic material the design of the structure it is applied to should not be ignored. Seek independent expert advice to ensure that the construction and design are suitable for the chosen system and will not cause the fairing material to crack or delaminate. Specification Data Volume Solids Specific Gravity Available Packs Base Converter Equipment Cleaning Typical Shelf Life Theoretical Coverage Application Methods WFT Batten, Trowel, Knife Theoretical Coverage Per Coat (at recommended DFT) Theoretical 0.154m²/lt Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size and application environment. VOC All VOC information contained herein is theoretical (unless otherwise stated). Actual VOC content may vary by batch and when tested via standard test methodology. Product As Supplied (without reducer) g/L Awlfair Pumpable Surface Preparation The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation. Mixing & Reduction Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. Mix the two components thoroughly to a uniform pink colour with no streaks or lumps. Warning: Do not add reducers, solvents or thinners of any kind to Awlfair Pumpable. 1:1 by volume (as supplied) 1.59:1 by weight of P7085/P7086 Awlfair Pumpable can be mixed using a suitable automatic mixing machine. The use of the mixing machine will generally increase the density of the product and will change the mechanical properties of the fairing compound. At the same time, automatic mixing equipment can provide productivity and health and safety benefits. Please consult your local technical representative for further advice regarding the use of automatic mixing equipment. Application Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary. Please ensure a risk assessment is carried out to assess the level of PPE required for the particular task undertaken when using this product. Do not use below 13°C/55°F or warmer than 40°C/104°F. Proper application and/or cure results may be more difficult to achieve when conditions are outside this range. Avoid conditions of low temperature with high humidity as this can result in the formation of a surface by-product that must be removed by either detergent wash followed by fresh water wash, or by sanding. Please refer to your local by trowel to or area you can work in 15-20 minutes. Start with thin coats of up to 6mm in low areas and build out to high areas. Apply Awlfair Pumpablerepresentative anvisit http://www.awlgrip.com for further information. Allow to cure. Several logo and other may be necessary in this publication areBlock and machine sand ©AkzoNobel grit paper. Remove air pockets and chamfer the Awlgrip, the AkzoNobel applications products mentioned to fill large areas. trademarks of AkzoNobel. with 40-60 2019 edges prior to refilling as appropriate. Remove sanding dust and residue before applying more Awlfair Pumpable. Stop when the faired surface meets the 1 of 2 fairing quality specified for the project. Ref:10417 Awlfair Pumpable

Open the catalog to page 1

Awlfair Pumpable can be mixed using a suitable automatic mixing machine. The use of the mixing machine will generally increase the density of the product and will change the mechanical properties of the fairing compound. At the same time, automatic mixing equipment can provide productivity and health and safety benefits. Please consult your local technical representative for further advice regarding the use of automatic mixing equipment. Product Data Sheet Awlfair Pumpable Application Application equipment and parameters are given as a guide. Actual equipment choices will vary according to...

Open the catalog to page 2