PRODUCT DATA SHEET AWLCRAFT® 2000 ACRYLIC URETHANE TOPCOAT (Code numbers can be found on Suggested List Price Schedule or Color Card) Features & Uses Awlcraft 2000 is a two component, fast drying acrylic urethane coating with long lasting gloss and color retention. Provides an easy to apply, buffable finish. Spray application only. Do not use below the waterline. Awlcraft 2000 is also available in a range of metallic colors (refer to separate datasheet). Specification Data Type: Two Component Acrylic Urethane Color: See Color Card and/or your Awlmix distributor. Packaging: Available in 1 gallon and 1 quart containers 2 2 Theoretical Coverage: Sq. Ft./Gallon; 573 Sq. Feet (53m ) at one mil dry (25 microns); 230 Sq. Feet (21m ) at recommended dry film thickness Calculated for mixed base and converter, reduced 25%. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 6-9 mils (150-225 microns) total of 3 or more coats. Recommended Dry Film Thickness: 2-3 mils (50-75 microns) total of 3 or more coats. Anticipated Cure Time at 77°F, 50% R.H: 24 Hours to tape free; 3 days to light service; 14 days for full cure. Recoatability: Typical spray applications consist of two to three coats applied over 1-4 hours. Exact time will vary with temperature, project size, and film thickness applied. AWLCRAFT 2000 topcoats which have been allowed to cure more than 24 hours must be sanded before recoating. VOC: Base: 472.5 g/lt or 3.9 lbs/gallon Spray Converter (G3010) 591g/lt or 4.9 lbs/gallon Application Equipment Conventional air atomized spray or HVLP spray. 2270 Morris Avenue • Union, New Jersey 07083 • USA • Tel: 908.686.1300 • Fax: 908.964.2219 Bannerlaan 54 • B-2280 Grobbendonk • Belgium • Intl. Tel: 32.14.257770 • Intl. Fax: 32.14.230880 76 Waterway Drive • Coomera • QLD 4209 • Australia • Tel: 61.7.5573.9655 or 1800.007.866 • Fax: 61.7.5573.9677 686 Rosebank Road • Avondale • Auckland • New Zealand • Tel: 64.9.828.3009 or 0800.150.527 • Fax: 64.9.828.1129 3 Neythal Road • Singapore 628570 • Tel: 65.6862.2928 • Fax: 65.6862.0778 Page 1 of 2 • Rev 6 – May 2013 AWLCRAFT 2000 ACRYLIC URETHANE TOPCOAT

PRODUCT DATA SHEET AWLCRAFT® 2000 ACRYLIC URETHANE TOPCOAT (Code numbers can be found on Suggested List Price Schedule or Color Card) SPRAY EQUIPMENT: Pressure Pot System: Devilbiss or equivalent: Spray Gun: JGA type Fluid Nozzle: AV-645-FX Fluid Needle Size: 1.1 Fluid Flow Rate: 170 - 270 ml/min Air Nozzle: AV-4239-43 GUN PSI: 2.5 – 3.5 bar (36-51 psi) Cup Gun System: Devilbiss or equivalent: Spray Gun: JGA type Fluid Nozzle: AV-4239-43 Fluid Needle Size: 1.1 Air Nozzle: AV-4239-43 GUN PSI: 2.0 – 3.0 bar (29-44 psi) Best results are achieved when sprayed over properly prepared AWLGRIP 545 Epoxy...