Catalogs >
Awlgrip >
Awlbrite Semi Gloss

Awlbrite Semi Gloss
2Pages

Catalog excerpts

PRODUCT DATA SHEET AWLBRITE SEMI GLOSS J3630 Features & Uses AWLBRITE Semi Gloss is a product developed for the professional to aid in the finishing of interior wood surfaces. AWLBRITE Semi Gloss provides a low sheen, 30° gloss finish for interior surfaces where a durable fast drying finish is required. The AWLBRITE product line provides a far more durable finish than varnish, is faster curing and as easy to apply. Do not use below the waterline. These products are recommended for interior use only. Specification Data Type: Three Component Acrylic Urethane. Color: J3630 – Clear Semi Gloss. Packaging: Gallons and Quarts. Theoretical Coverage - Sq. Feet/Gallon: 930 Sq. Feet (86 m²) at 1 mil dry (25 microns); 93 Sq. Feet (8.6 m²) at recommended dry film thickness of 10 coats. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 2.0-2.5 mils (50-62 microns) per coat. Recommended Dry Film Thickness: 1.0-1.2 mils (25-30 microns) per coat. Anticipated Cure Time at 77°F (25°C) /50% R.H: 3 hours to recoat; 12 hours to light service; 7 days for full cure. Recoatability: With itself: 3 hours minimum, 24 hours maximum without sanding or scuffing. VOC: Semi Gloss (J3630) - 352 g/lt or 2.9 lbs/gallon Converter (J3006) – 146 g/lt or 1.2 lbs/gallon Application Equipment Conventional air atomized spray or HVLP spray. J3630 can also be applied by brush with excellent results. Do take care to apply thin, smooth coats to avoid uneven gloss level (when applied by brush). SPRAY EQUIPMENT Pressure Pot System Binks or equivalent: Spray Gun: #95 Fluid Nozzle: #63BSS (.046” Orifice Size) Fluid Needle: #663A Air Nozzle: #63PB Pressure pot gauge should read 8 to 12lbs With 50 to 60 lbs atomisization. Siphon or Cup Gun System Binks or equivalent: Spray Gun: #95 Fluid Nozzle: #66SS (.070” Orifice Size) Fluid Needle: #665 Air Nozzle: #65SK Atomizing air pressure should be approximately 50 to 60 lbs. All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. ©AkzoNobel 2015 Page 1 of 2 - Rev 8 – January 2015 - AWLBRI

Open the catalog to page 1

PRODUCT DATA SHEET AWLBRITE SEMI GLOSS J3630 High Volume Low Pressure System Binks MACH 1 or equivalent pressure pot: For use with all Awlgrip Topcoats and low viscosity primers. Fluid Nozzle: #91 (.040” Orifice Size) #92 (.046” Orifice Size) Fluid Needle: #54-4382 Air Nozzle: #93P Surface Preparation The wood should be clean, dry, smooth, and well seasoned, with less than 15% moisture content. Ideally AWLBRITE Semi-Gloss is applied as a finish coat. Apply AWLBRITE Semi-gloss to wood that has been sealed with Awlbrite Quik-Fil, Awlbrite Clear or Awlspar. Note: Due to the wide variety of...

Open the catalog to page 2