PRODUCT DATA SHEET AWL®FAIR L W FAST CURE D8200/D7222 Features & Uses AWLFAIR L.W. FAST CURE is a premium Trowelable product for fairing, leveling or smoothing surface imperfections due to gouges, pitting, dents or weld seams. The Awlfair LW formulation brings you the latest technology with super smooth finish and easy sanding. Awlfair LW is suitable for both manual and automatic mixing. Backed by extensive laboratory research and development Awlfair LW has been tested and approved for a multitude of systems. May be used above or below the waterline Specification Data Type: Two Component Epoxy. Color: White base, red converter. Pink – after mixing components. Packaging: Available in 1 quart containers, 1 Gallon containers , 2 gallon containers. Theoretical Coverage: Sq. Feet/Gallon: 1,463 Sq. Feet (136m 2) at one mil dry (25 microns) DFT. 2 5.9 Sq. Feet (0.54m ); ¼ inch; 250 mils (6,350 microns) DFT. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 250 mils (6350 microns) per coat. Maximum 400 mils (1cm) per coat. Number of coats: As required. Cure Time at 75°F/25°C/50% R.H: 7 hours resistance to foot/tread; 7 days full cure. Recoatability: Awlfair® LW must be sanded before recoating with itself or other Awlgrip Product. It must be overcoated with an epoxy primer such as HIGH BUILD, EPOXY SPRAYABLE FAIRING COMPOUND, HULLGARD, ULTRABUILD before applying the finishing system. This is to reduce the risk of print through of the fairing compound profile. AWLFAIR LW is sandable after 17 hrs at 55°F/13°C, 6 hrs at 77°F/25°C and 90 mins at 95°F/35°C Shore D hardness development after 7 days: >60 at 77°F/25°C VOC: White Base (D8200) – 0 g/lt or 0 lbs/gallon Fast Converter (D7222) – 185 g/lt or 1.54 lbs/gallon Mixed (1:1 by volume) – 93 g/lt or 0.77 lbs/gallon Application Equipment Trowels, Spatulas, longboard or Putty Knives. Surface Preparation Only apply over properly applied and prepared Awlgrip Primers. Hullgard Extra Epoxy Primer and High Build are recommended substrate primers. Awlfair LW may be applied direct to Hullgard Extra without the need for sanding. See the relevant primer product datasheet for details. High Build must be sanded prior to application of Awlfair LW. All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. ©AkzoNobel 2015 Page 1 of 2 - Rev 3 – January 2015 - A

PRODUCT DATA SHEET AWL®FAIR L W FAST CURE D8200/D7222 Mixing and Reduction Mix by volume 1:1 D8200:D7222. Mix ratio by weight 1.56:1 D8200:D7222 Thoroughly mix material to a uniform pink color with no streaks or lumps in the mix. Induction Time after Mixing: None Pot Life at 50% RH: 55°F / 13°C: 80 mins 75°F / 25°C: 30 – 35 mins 95°F / 35°C: 15 – 20 mins Do not add thinners or reducers to AWL-FAIR L.W. Application Instructions Properly prepare and prime the surface with the recommended primer before starting to fill or fair. Apply Awlfair L.W. by trowel to an area you can work in 5 to 10 minutes....