PLAQUE MFM18240
12Pages

PLAQUE MFM18240 UNDERWATER LIGHT Operating Instructions

PREFACE PRECAUTIONS The PLAQUE series underwater lights are designed to use the latest LED lighting technology for flush-mount installation where the most important are low-profile casings to avoid high water resistance and quality materials to assure very reliability installation and operation. All the models are available in aluminium bronze casings. The lighting is available in white, blue or green colors or three-color. All the models are designed with 18 power LEDs and suitable power supply units. FEATURES Aluminium Bronze or Anodized Aluminium Casing 18 Power LEDs Design White, Blue,...

CONTROLS AND CONNECTORS Underwater Light PLAQUE MFM18240 5 3 2 1 4 (1) Optical window The 6 mm depth tempered glass optical window. (2) Underwater light casing Aluminium bronze casing with fixing holes and cable gland. (3) Fixing assembly The fixing nut, washer and screws to fix the underwater light on the hull. (4) Cable The 8-pole multi-core cable to connect the power supply unit. (5) Heat sink The aluminium heat sink to enable properly temperature stability of the underwater light. 4

INSTALLATION The underwater light kit consists of the following components: Underwater Light PLAQUE MFM18240 Power Supply Unit MPS06800 Washer Fixing nut with 4 screws M8 and bonding screw M4 2 x cable gland M12 Operating Instructions with Declaration of Conformity and Warranty conditions Underwater Light PLAQUE MFM18240 The PLAQUE MFM18240 has to be installed on a flat surface of the hull of the vessel. Do not try to install the underwater light while the vessel is in the water. When the installation is finished briefly test the underwater light prior to launching the vessel. The...

Note: To install the underwater light on the steel hull it is highly recommended to use the optional isolation board (not included) between the hull and underwater light casing to prevent galvanic corrosion. Note: Do not overtighten the screws as this can result in hull or underwater light damage. Bonding The underwater light has to be connected to the vessels bonding and cathodic protection using a pretinned wire a minimum of 8 AWG (8.36 mm2) with green insulation or green with a yellow stripe. The wire has to be connected to the underwater light by the help of the bonding screw M4 located...

Power supply connection The power supply has to be connected through the switch (not included) and protected by a fuse (not included) to the DC IN terminal-block connector with correct polarity. The power supply voltage has to be from 10 - 30Vdc. A power supply unit of another underwater light can be connected to the DC OUT terminal-block connector. Note: Only one additional power supply unit of the same model number can be connected to the DC OUT terminal-block connector and suitable power supply cable should be used. The appurtenant cap should be removed from the casing and enclosed cable...

APPEARANCE 40 Ø1 85 96 190 TECHNICAL SPECIFICATIONS LED Underwater Light PLAQUE MFM18240 Power requirement 3x800 mA Lens angle 50° Optical window 6 mm depth tempered glass Luminous flux 3.900 lm White color temperature 10.000 K Operating temperature -10C - +50C Casing Aluminium bronze (AB2) Protection IP 68 Dimensions Ø140x190mm Weight 6.7 kg Power Supply Unit MPS06800 Input voltage Consumption Operating temperature Casing Protection Dimensions Weight 12-24 Vdc max. 5.4 Adc/12 Vdc or 2.5 Adc/24 Vdc -10C - +50C Polycarbonate IP 65 200x160x55.5mm 0.6 kg Design and specifications subject to...

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written...

DECLARATION OF CONFORMITY according to IEC Guide 22 and EN 45014 Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Underwater Light PLAQUE MFM18240 with Power Supply Unit MPS06800 conform to the following Product Specifications: EMC: EN 55022 (CISPR 22: 1993) EN 50130-4: 1994 Safety: EN 60950 EN 60529 Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CEmarking...