PLAQUE MFM0680 UNDERWATER LIGHT Operating Instructions

PREFACE PRECAUTIONS The PLAQUE series underwater lights are designed to use the latest LED lighting technology for flush-mount installation where the most important are low-profile casings to avoid high water resistance and quality materials to assure very reliability installation and operation. All the models are available in aluminium bronze casings. The lighting are available in white, blue and green colors. All the models are designed with 6 power LEDs and suitable power supply units. • • • • • FEATURES • • • • • • • • • • Aluminium Bronze Casing 6 Power LEDs Design White, Blue or Green Lighting...

CONTROLS AND CONNECTORS Underwater Light PLAQUE MFM0680 5 3 2 4 1 (1) Optical window The 6 mm depth tempered glass optical window. (2) Underwater light casing Aluminium bronze casing with fixing holes and cable gland. (3) Fixing assembly The fixing nut, washer and screws to fix the underwater light on the hull. (4) Cable The 4-pole multi-core cable to connect the power supply unit. (5) Heat sink The aluminium heat sink to enable properly temperature stability of the underwater light. 4

Power Supply Unit MPS02800 (1) LIGHT Terminal-block connector to connect the LED underwater light using 4-pole multi-core cable. (2) CONTROL Terminal-block connector to connect optional remote control unit or switch. (3) DC IN Terminal-block connector to connect 12-24Vdc power supply. (4) DC OUT Terminal-block connector to connect to the DC IN connector of another power supply unit. 5

INSTALLATION The underwater light kit consists of the following components: • Underwater Light PLAQUE MFM0680 • Power Supply Unit MPS02800 • Washer • Fixing nut with 4 screws M8 and bonding screw M4 • 2 x cable gland M12 • Operating Instructions with Declaration of Conformity and Warranty conditions Underwater Light PLAQUE MFM0680 The PLAQUE MFM0680 has to be installed on a flat surface of the hull of the vessel. Do not try to install the underwater light while the vessel is in the water. When the installation is finished briefly test the underwater light prior to launching the vessel. The installation...

Note: • To install the underwater light on the steel hull it is highly recommended to use the optional isolation board (not included) between the hull and underwater light casing to prevent galvanic corrosion. Note: • Do not overtighten the screws M8 as this can result in hull or underwater light damage. Bonding The underwater light has to be connected to the vessels bonding and cathodic protection using a pretinned wire a minimum of 8 AWG (8.36 mm2) with green insulation or green with a yellow stripe. The wire has to be connected to the underwater light by the help of the bonding screw M4 located...

A power supply unit of another underwater light can be connected to the DC OUT terminal-block connector. Note: • Only one additional power supply unit of the same model number can be connected to the DC OUT terminal-block connector and suitable power supply cable should be used. The appurtenant cap should be removed from the casing and enclosed cable gland M12 should be inserted. Underwater light connection The underwater light has to be connected to the LIGHT terminal-block connector as described in the table below: MPS02800 terminal-block connector LIGHT 1 2 3 4 PLAQUE MFM0680 wire colour FUNCTION...

APPEARANCE Ø 50 64 0 11 135 TECHNICAL SPECIFICATIONS LED Underwater Light PLAQUE MFM0680 Power requirement 800 mA Lens angle 50° Optical window 6 mm depth tempered glass Luminous flux 1.300 lm White color temperature 10.000 K Operating temperature -10°C - +50°C Casing Aluminium bronze (AB2) Protection IP 68 Dimensions Ø110x135mm Weight 2.3 kg Power Supply Unit MPS02800 Input voltage Consumption Operating temperature Casing Protection Dimensions Weight 12-24 Vdc max. 1.8 Adc/12 Vdc or 0.8 Adc/24 Vdc -10°C - +50°C Polycarbonate IP 65 127x111x55.5mm 0.3 kg Design and specifications subject to change...

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement...

DECLARATION OF CONFORMITY according to IEC Guide 22 and EN 45014 Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Underwater Light PLAQUE MFM0680 with Power Supply Unit MPS02800 conform to the following Product Specifications: EMC: EN 55022 (CISPR 22: 1993) EN 50130-4: 1994 Safety: EN 60950 EN 60529 Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CEmarking accordingly:...