Operating Instructions

The EQUATOR MSR0640 series of a compact ultra-thin underwater light with built-in driver is designed to use the latest LED lighting technology. The surface-mount designed casing enable very simple installation on the stern and both sides of the hull without making any bigger holes through the hull under waterline. All the models are available in aluminium bronze or stainless steel casings. The lighting is available in white, blue or green colors with 6 power LEDs. The multi-color RGB version allows changing of the color of lighting manually or automatically through the complete rainbow spectrum....

(1) Optical window High-grade polycarbonate glass optical window. (2) Underwater light casing Aluminium bronze casing with fixing holes and cable gland. (3) Cable The 4-pole multi-core cable to connect the 12-24Vdc power supply and optional remote control or switch. (4) Fixing screw The fixing screws to fix the underwater light on the hull.

INSTALLATION The underwater light kit consists of the following components: • Underwater Light EQUATOR MSR0640 • 4 x fixing screw M6x80 with nut M6 and washer • Operating Instructions with Declaration of Conformity and Warranty conditions The EQUATOR MSR0640 has to be installed on a flat surface on the stern or both sides of the hull of the vessel. Do not try to install the underwater light while the vessel is in the water. When the installation is finished briefly test the underwater light prior to launching the vessel. The installation have to be realized by a qualified personnel. Note: • Avoid...

Note: • All the stainless steel fixing screws (M6x80) it is highly recommended to be sealed in the contact with underwater light casing by optional TEF-GELTM waterproof paste (not included) to prevent galvanic corrosion. Note: • To install the underwater light on the steel hull it is highly recommended to use the optional isolation board (not included) between the hull and underwater light casing to prevent galvanic corrosion. Note: • Do not overtighten the screws as this can result in hull or underwater light damage. Bonding The underwater light has to be connected to the vessels bonding and...

Multi-color (M) model To control the mode of lighting the simple momentary-switch (not included) has to be used and connected to the CONTROL wires by the 2-pole signal cable (not included). Optional MXU01 or MXU03 interfaces can be connected to the CONTROL wires by using a 2-pole signal cable (not included). CONTROLS Single-color white (W), blue (B) or green (G) models Remote control can be used to turn-on and turn-off the underwater light and to control the luminosity. Dimming The dimming are enabled by using optional PWM dimmer MDU13. DMX512 control The network connection to control the lights...

Set default Press the momentary switch for min. 40 seconds or until the light is turned off. Synchronization When more than one multi-color underwater light is connected to the system the optional Synchronization Unit MSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting. On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode. If the multi-color light is used only with one of the fixed color of lighting the synchronization is not necessary. DMX512...

TECHNICAL SPECIFICATIONS Power supply Lens angle Optical window Luminous flux White color temperature ASTEL protocol default address Operating temperature Casing Protection Dimensions Weight 12 – 24 Vdc, max. 680 mA/12 Vdc or 380 mA/24 Vdc 60° High-grade polycarbonate glass 950 lm 6.000 - 10.000 K 1 -10°C - +50°C Aluminium bronze (AB2) or stainless steel (SAE316L) IP 68 99 x 69 x 10 mm 0.3 kg Design and specifications subject to change without notice.

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement...

DECLARATION OF CONFORMITY according to IEC Guide 22 and EN 45014 Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Underwater Light EQUATOR MSR0640 conform to the following Product Specifications: EMC: Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CEmarking accordingly: -the Low Voltage Directive 2014/35/EU -the EMC Directive 2014/30/EU -the RoHS Directive (EU)2015/863...