video corpo

AL250_AL600WA

AL250_AL600WA

AL250_AL600WA

Product catalog summary
Introduction
This document provides installation and maintenance instructions for the AL250WA and AL600WA underwater hull lights, designed for marine, industrial, and domestic applications. It emphasizes the importance of reading the manual to avoid risks such as electric shock, injury, fire, or equipment damage.

Features
The lights use 250 & 600 watt halogen bulbs with a 4600 K reflector. They allow easy lamp replacement through rear access and have a thermal management system to dissipate heat. The housing is made from high-quality aluminum, and the lens is crafted from borosilicate glass. The fixture includes user-friendly hardware and a leveling ring for installation.

Specifications
  • Body and Lens Bezel: Aluminum
  • Lens: 0.5” thick borosilicate glass
  • Seals and Gaskets: High temperature silicone rubber
  • Fixture Weight: 19.0 lbs
  • Cutout Size: 4.5” (33mm)
  • Hull Thickness: 0.25” to 5” (5mm to 90mm)
  • Water Ingress Protection: IP66
  • Electrical: Dual ballast, 120/240/280 volts, 1.5-0.75 amps running current, 9.25 amps mains current draw, 90% power factor


Operation and Maintenance
The light must be operated underwater for cooling. Halogen lamps have a service life of about 6,000 hours. The document provides detailed steps for lamp replacement, emphasizing safety and cleanliness. Regular maintenance includes checking the lens for marine growth and ensuring the housing is electrically bonded to the vessel's grounding system.

Safety and General Information
Installation should be performed by trained professionals. The light must be fully submerged during operation, and the housing should be bonded to the vessel's cathodic protection system to prevent corrosion. Any signs of damage or water ingress should be addressed immediately.

Warranty
Aqua Lights offers a 1-year warranty on defects in parts and workmanship, with a lifetime warranty on bronze fixtures. The warranty excludes bulbs and damages from misuse or unauthorized modifications. Aqua Lights' liability is limited to repair or replacement, excluding expenses related to vessel haul-outs or labor.

Contact Information
Aqua Lights, 785 Branch Dr, Alpharetta, GA 30004. Phone: 1-866-924-2782. Website: www.AquaLights.org. Email: [email protected].
See more

Catalog excerpts

AL250_AL600WA-1

Underwater Hull Light

 Open the catalog to page 1
AL250_AL600WA-2

This underwater light has been carefully designed to provide a versatile product of the highest quality, suitable for a wide range of underwater applications such as marine, industrial and domestic. WARNING! Sections in this manual identify safe practice. It is of the utmost importance that this manual is carefully read and understood. Failure to do so may result in electric shock, injury, fire, or equipment damage. PLEASE READ CAREFULLY and, if in doubt, seek professional advice. Light source: 250 & 600 watt Halogen Bulb with reflector 4600 K. Lamp replacement: The unit features rear access...

 Open the catalog to page 2
AL250_AL600WA-3

WARNING: Never operate the light out of water as the water provides necessary cooling. The lens bezel must be completely submerged at all times. Avoid operating the light when the boat is planning as often times this raises the fixture bezel above the water-line and thus diminishing the cooling effect of the water. Generally, Halogen lamps have a service life of approximately 6,000 hours. This may vary depending on the number of restarts and other factors. Isolate mains power and assure it can not be re energized accidentally by other persons. Allow the lamp and housing to cool down (minimum...

 Open the catalog to page 3
AL250_AL600WA-4

Socket. IMPORTANT! Ensure the new lamp is wiped totally clean of any dirt or fingerprints. Failure to do so will result in premature lamp burn-out. Inspect the housing to ensure it is completely clean and dry. The lens may be cleaned if neces- sary using a soft cloth on the end of a wooden dowel or similar. Re inspect after cleaning to en- sure no cloth or other cleaning fibers remain inside the housing. NEVER! Spray lubricants, degreasing agents or other similar products into the housing. Carefully re-fit the lamp assembly into the housing ensuring the front end of the reflector case locates...

 Open the catalog to page 4
AL250_AL600WA-5

If the housing shows signs of excessive corrosion (other than surface contamination) or physical damage, the vessel should be hauled so a complete assessment can be performed. Any signs of water ingress must be addressed immediately. Any suspect equipment must be repaired or replace. The Lens and Bezel have been carefully designed with a smooth, flush surface to allow easy Never operate the vessel with the lamp housing end cap removed. Limited Warranty Aqua Lights warrants these fixtures to be free of defects in parts and workmanship for 1-year from the date of shipment. Bronze fixture has a...

 Open the catalog to page 5
AL250_AL600WA-6

250 Watt Mega Blaster - Customer Assembly Drawing

 Open the catalog to page 6

Archived catalogs

  1. ALUC

    1  Page

  2. AL175WS

    7  Pages

  3. AL75WA

    7  Pages

  4. AL75H

    12  Pages

  5. al60lp-w

    1  Page

  6. AL35X

    12  Pages

  7. AL35H

    12  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.