Document Library TS Data Sheet 08017 08027 08019 08029 Status: Active 3M™ Marine Grade Silicone Sealant Data Sheet 3M Part No.(s) 08017 08027 08019 08029 3M Part Descriptor(s) 3 fl. oz. tube (90 ml) - White 10 fl. oz. cartridge (295 ml) - White 3 fl. oz. tube (90 ml) - Clear 10 fl. oz. cartridge (295 ml) - Clear Description A mildew resistant, non-sagging, moisture curing silicone rubber sealant for above the waterline applications which remains flexible with excellent resistance to the marine environment. Adheres to bare and painted metal, glass, fiberglass, non-oily woods and many plastics and abraded rubber. Features l l l l l l l Mildew resistant Flexible polymer One-part cure Excellent weathering resistance High temperature resistant Non-shrinking Non-sagging formula Typical Physical Properties Container 3 fl. oz. tube (90 ml) - White/Clear 10 fl. oz. cartridge (295 ml) White/Clear Base Density lbs/Gallon (Appx.) Color Flash Point - °F Solids Content (Appx.) Consistency Service Temperature - °F

Tack Free Time Cure Time (1/8" Thick) Specific Gravity Coverage (10 oz.) Performance Properties 180° Peel Strength - One inch (2.54 cm) wide specimen on canvas Substrate Relative Humidity Strength lbs/inch width Failure Mode* * Cohesive Bond - Adhesive/Sealant fails before adhesive/sealant releases from substrate. This is the desired mode . Adhesive Failure - Adhesive/Sealant releases from substrate. Overlap Shear Strength - One inch (2.54 cm) overlap specimens (0.093 inch (0.2362 cm) thickness). Substrate Relative Humidity Failure Mode*

Stainless Steel * Cohesive Bond - Adhesive/Sealant fails before adhesive/sealant releases from substrate. This is the desired mode . Adhesive Failure - Adhesive/Sealant releases from substrate.

Tensile & Elongation Test: A 1/8 inch (0.3175cm) dumbbell specimen with a 1/8 inch (0.3175) square cross section was tested at 2.0 inches/minute (5.08 cm/minute). Relative Humidity Tensile Strength 2 psi (kg/cm ) Application Information Directions for Use Surface Preparation: There are waxes, coatings, sealants, grease, oil and other contaminants used in the marine industry, making it very important to TM clean all surfaces to be bonded before applying 3M Marine Grade Silicone Sealant. Recommended procedures include cleaning with 3M TM General Purpose Adhesive Cleaner, P. N. 08984. When using...

Temperature - Do not apply at temperatures below 40°F (4°C) or on frost covered surfaces. Abrading the surfaces with a 180 grit to 220 grit abrasive will enhance the bond strength. Cut tip to desired bead size, puncture seal in TM nozzle. Place cartridge in a caulk gun. Apply 3M Marine Grade Silicone Sealant to the seam or part to be sealed. Position parts. Tool material to desired appearance. Remove excess with General Purpose Adhesive Cleaner, P. N. 08984. Cleanup: TM For cleaning 3M Marine Grade Silicone Sealant before it is cured, use a dry cloth to remove the majority of sealant, followed...

Recommended Storage Temperature Range: 60°F(15°C) to 80°F(27°C) Expected Shelf Life at Recommended Storage Temperature: 36 Months Precautionary Information Refer to Product Label and Material Safety Data Sheet for Health and Safety Information before using this product. Country US This document is public. It may be distributed. Important Notice to Purchaser Technical Data: All physcial properties, statements and recommendations are either based on tests we believe to be reliable or our experience, but they are not guaranteed. 3M recommends each user determine the suitability of the products for...