Product Description 3M™ Marine Adhesive Sealant 5200 is a one-part polyurethane that chemically reacts with moisture to deliver strong, exible bonds. It has excellent adhesion to wood, gelcoat, and berglass. It forms a watertight, weather-resistant seal on joints and boat hardware, above and below the waterline. In addition, its exibility allows for dissipation of stress caused by shock, vibration, swelling or shrinking. Product Features • Tough/ exible polyurethane polymer • One component, moisture curing • Long working time • Bonds dissimilar materials • Non-shrinking • Adheres to a w

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Technical Information Note The following technical information and data should be considered representative or typical only and should not be used for speci cation purposes. Typical Uncured Physical Properties Property Caulkable, non-sag paste Typical Mixed Physical Properties Property Test Condition Tack Free Time Tack Free Time Room Temperature Typical Cured Characteristics Shore A Hardness: 68 Methods ASTM C661 Typical Performance Characteristics Property Tensile Strength Service Temperature Range Test...

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Typical Performance Characteristics (continued) Overlap Shear Strength 48 kg/cm² Substrate Notes Notes One inch (2.54 cm) overlap specimens (0.093 inch [0.2362 cm] thickness) Cohesive – Adhesive/Sealant fails before adhesive/sealant releases from substrate. This is the desired mode. Adhesive Failure – Adhesive/Sealant releases from substrate. Desirable failure mode is cohesive. One inch (2.54 cm) overlap specimens (0.093 inch [0.2362 cm] thickness) Cohesive – Adhesive/Sealant fails before adhesive/sealant...

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Typical Performance Characteristics (continued) Overlap Shear Strength 28 kg/cm² Substrate Notes Notes One inch (2.54 cm) overlap specimens (0.093 inch [0.2362 cm] thickness) Cohesive – Adhesive/Sealant fails before adhesive/sealant releases from substrate. This is the desired mode. Adhesive Failure – Adhesive/Sealant releases from substrate. Desirable failure mode is cohesive. One inch (2.54 cm) overlap specimens (0.093 inch [0.2362 cm] thickness) Cohesive – Adhesive/Sealant fails before adhesive/sealant...

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Typical Performance Characteristics (continued) Overlap Shear Strength 15 kg/cm² Substrate Notes Acrylic (PMMA) Plastics/Polymers inch (2.54 cm) overlap specimens (0.093 inch One [0.2362 cm] thickness) Test Condition Cohesive – Adhesive/Sealant fails before adhesive/sealant releases from substrate. This is the desired mode. Adhesive Failure – Adhesive/Sealant releases from substrate. Desirable failure mode is cohesive. 12 kg/cm² Plastics/Polymers inch (2.54 cm) overlap specimens (0.093 inch One [0.2362 cm]...

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Typical Performance Characteristics (continued) E ect of Water Submersion: Conditions Test Condition: Room Temperature Additional Information Notes: Dumbbell specimen with 1/8” length, 1/8” square cross section were tested at 2.0 inches/minute. Typical Physical Properties Solids Content by Weight: 97 % Handling/Application Information Directions for Use Surface Preparation: There are waxes, coatings, sealers, greases, oils and other contaminants used in the marine industry, making it very important to clean...

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Handling/Application Information (continued) - Do not apply at temperatures below 40°F (4°C) or on frost covered surfaces. Do not apply at surface temperatures above 100°F (38°C). - Sealant should be used within 24 hours after inner seal is punctured, as product will start to cure in the cartridge and nozzle. - At 90o F (32o C) and 90% relative humidity, bonds should be made within 15 minutes. - Some one-part solvent-based Marine paints may not cure on top of cured 5200. It is strongly recommended to test...

3M™ Marine Adhesive Sealant 5200: 06500 • 05203 • 05206 • 21463 • 06504 • 05205 • 06502 Information Technical Information: The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills su cient to assess and apply their own informed judgment to the information. No license under any 3M or third party...