RUBBER-MOLDED_lres1
1 / 39ページ

RUBBER MOLDED SERIES Table of Contents Rubber Molded Bulkhead Connector Mates . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . Typical Right Angle and Straight Connector Indexing . . . Typical Mated Assembly and Options . . . . . . . . . . . . . . . . . RMA-FS and Associated Parts . . . . . . . . . . . . . . . . . . . . . . RMG-FS R/A . . . . . . . . . . . . . . . . . . . . . . ....

RUBBER MOLDED BULKHEAD CONNECTOR MATES VISUAL INDEX RMA-BCL XSA-BCL VMA-BCL VSA-BCL NOTE: Torque values ref renced in this literature assume installation into e dry metal threads. Please contact the actory f r recommendations. f o VMF-BCL VSF-BCL XSFDE-BCL (f rmerly XSDE-BCL) o 50-17 LSG-BC SC (f rmerly LSK-BC SC) o

NOTE: Torque values re§renced in this literature assume installation into dry metal threads. Please contact the fcctory Or recommendations.

EiHEQSEIH Our standard rubber molded series typically consists of an in-line female neoprene connector mated to a glass reinforced epoxy (XS) bulkhead connector. Various sizes are available ranging from single contact connectors up through 12 contact connectors. Most are available with pins and sockets reversed to help prevent mismating of connectors, which otherwise look identical. This also allows for socket type contacts in a connector where there is a possibility of a "power-on" situation. Many of the bulkhead type connectors are available in 316 Stainless Steel, and can also be...

APPLICATIONS: Standard, Reversed Rubber Molded Series Applications requiring light to medium ruggedness Hazardous environments Field installable applications Glass Reinforced Epoxy Series Applications requiring medium ruggedness Hazardous environments Power transmission Signal telemetry Metal Shell Series Applications requiring heavy ruggedness Hazardous, rugged environments Power transmission Signal telemetry CABLE: Rubber Molded Series Connector's power capability may be limited by amperage and voltage rating of cable to which it is molded to. With the exception of field installable...

MAINTENANCE PROCEDURES CONNECTORS MAINTENANCE The following procedures detail the maintenance requirements for the Rubber Molded Series and their associated parts. Even though this procedure appears simple, only qualified technicians should perform the maintenance. If connectors are periodically unmated SEA CON® recommends the following: 1. Before unmating ensure connectors are free of foreign contaminates. Visually check for and note any damage or abnormalities. After unmating visually check for and note any damage, cuts or abnormalities. Clean any grease, moisture or foreign particles...

RUBBER MOLDED SERIES TYPICAL RIGHT ANGLE AND STRAIGHT CONNECTOR INDEXING Visual Index Optional Locking Sleeve Cable (Straight Entry) Right Angle Molded Body (Elastomeric Material) Cable (Right Angle Entry To Connector) Cable-Right Angle Entry-In Line With Index In the case of right angle connectors, the cable is always perpendicular to the index, as shown

RUBBER MOLDED SERIES TYPICAL MATED ASSEMBLY AND OPTIONS CABLE Neoprene outer jacket supplied on our standard cables CABLE Or solid rubber for dummy RUBBER MOLDED CONNECTOR RUBBER MOLDED CONNECTOR OPTIONAL LOCKING SLEEVE (long) For use with straight connectors only. This long type of locking sleeve helps to eliminate conductor breakage at termination joint by eliminating flexing at joint area. RIGHT ANGLE CONNECTOR ELECTRICAL CONTACTS copper alloy, hard gold plated per ASTM-B-488. OPTIONAL LOCKING SLEEVE For use with straight or right BULKHEAD CONNECTORS Material -Glass Reinforced Epoxy...

RMA-FS AND ASSOCIATED PARTS STANDARD RUBBER MOLDED IN-LINE SERIES Material: Special Neoprene, molded Contacts: Copper Alloy, Hard Gold Plated per ASTM B488 Cable: 1 N 2 Voltage Rating: 600 VDC-contact factory for higher voltage requirements Pressure Rating, Mated: up to 20,000 psi SLIP-ON SERIES Notes: Specify exact wire diameter when ordering. Maximum wire DIA=0.09 inch Material: Special Neoprene, molded Contacts: Brass, Hard Gold Plated per ASTM-B-488 Voltage Rating: 600 VDC-contact factory for higher voltage requirements Pressure Rating, Mated: up to 20,000 PSI SOLDER CUP VISUAL INDEX...

RMA-FS AND ASSOCIATED PARTS MATEABLE BULKHEAD CONNECTORS BULKHEAD CONNECTORS & MOUNTING REQUIREMENT (MATES TO RMA-FS & RMA-FS-R/A & RMA FS SL) Dummy Connector: RMF FSD Part Name: RMA-BCL Material: 316 Stainless St., Internal Insulation-Special Neoprene Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488 Pressure Rating, Mated: up to 20,000 psi RMA-BCL; Special insulating neoprene is compression molded to the metal body forming a reliable seal. The metal body can be made of stainless steel, aluminum or other metals. This Connector utilizes a facial o-ring seal to the bulkhead. O-RING...

RMA-FS AND ASSOCIATED PARTS MATEABLE BULKHEAD CONNECTORS BULKHEAD CONNECTORS & MOUNTING REQUIREMENT (MATES TO RMA-FS & RMA-FS-R/A & RMA FS SL) Dummy connector RMA FSD Part Names: XSC-BC, XSC-BCL Material: Glass Reinforced Epoxy Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488 Pressure Rating, Mated: up to 10,000 psi XSC-BC, XSC-BCL; These connectors feature a radial type o-ring seal, good for up to 10,000 PSI, mated. Available only in single contact. 3/8-24 UNF Mounting Torque 12 INCH LBS. 3/8-24 UNF-2B THREAD MOUNTING REQUIREMENT 3/8-24 UNF Mounting Torque 12 INCH LBS. NOTE: Torque...

VMA-FS AND ASSOCIATED PARTS REVERSED RUBBER MOLDED IN-LINE SERIES Material: Special Neoprene, Molded Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488 Cable: 1 N 2 Voltage Rating: 600 VDC-contact factory for higher voltage requirements Pressure Rating, Mated: up to 20,000 psi SLIP-ON SERIES Notes: Specify exact wire diameter when ordering. Maximum wire DIA=0.09 INCH Material: Special Neoprene, Molded Contacts: Copper Alloy, Hard Gold Plated per ASTM-B-488 Voltage Rating: 600 VDC-contact factory for higher voltage requirements Pressure Rating, Mated: up to 20,000 psi SOLDER CUP (Uses...