カタログ >
Sea Hawk >
Tuff Stuff High-Build Epoxy Primer

Tuff Stuff High-Build Epoxy Primer
1 / 2ページ

カタログの抜粋

Tuff Stuff High Build Epoxy Primer Superior Blister Prevention & Repair 1284, 1285 Highest Build Epoxy Primer Extremely Durable Easy Application, Longer Windows Fewer Coats Needed Features and Benefits Product Description Tuff Stuff is an extremely high-build two-part epoxy primer that dries fast, enabling application of a complete barrier system and bottom paint in just two days. Using microsheet silicate technology, millions of microscopic sheets overlap and build a 100% water barrier that protects the surface from moisture and water penetration. Tuff Stuff is effective for blister prevention on fiberglass, or as a bilge coating, because it is resistant to oil and water. As a universal primer, it can be used for corrosion protection on most metals below the waterline, and for priming any metal. Tuff Stuff creates an overlapping barrier to eliminate any direct path for water migration. Use over blistered fiberglass as a repair coat, and over unblistered fiberglass as a barrier coat. Protects metals from corrosion, including: aluminum, bronze, stainless steel, cast iron and lead – above and below the waterline. Excellent for priming props, shafts, keels, trim tabs, thru hulls and lower units Highest build epoxy – Fewer coats needed Longer window between coats makes Tuff Stuff easy to use Reduced labor and less haul out time Application Controls Product Information Colors: Light Gray-1284, White- 1285 Finish/Sheen: Matte Volume Solids: 52% +\- 2% Available Sizes: 1/2 Gallon Kit (2 quarts), 2 Gallon Kit (2 gallons) Shipping Weight: 25 Lbs./2 Gallon Kit Method: This product may be applied by airless and conventional spray, solvent resistant rollers and brushes. Dry Times and Overcoating Intervals in Hours: Substrate Temp. Touch Min Max Recoat Maximum Overcoat 2 hr 3 hr 6 days 24 hrs Mix Ratio: 1:1 Side A, Side C Induction Time: 20-30 minutes Flash Point: 80° F VOC: 444 Grams/Liter Typical Film Thickness: 6-7.5 mils dry film thickness (DFT) per coat, (11.5-14.5 mils wet film thickness (WFT)) Recommended Coats: 2-4 depending on intended service Theoretical Coverage: 140 Sq.Ft./Gal. @ 6.0 mils DFT 73°F (23°C) When overcoating Tuff Stuff Epoxy Primer with a solventbased coating it is important to meet the required over coating times in order to achieve the best adhesion because temperature and humidity control dry times. (Exception: Overcoating with a water-based coating: see Tech Bulletin TSWB-1284) An easy rule in epoxies is when the coating is dry to the touch, yet still has some tack, it is ready to be over coated. (Thumb print without lifting any epoxy.) However, if the coating is completely cured (or after 24 hours) it needs to be thoroughly sanded with 80 grit sand paper to remove shine, or you must apply another coat of Tuff Stuff within 6 days, no longer. Then you have an additional 24 hour maximum to overcoat with antifouling paint. Tuff Stuff immersion should minimum of 24 Hours after application. Revised 8/10/2012 NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX 727.523.7325 www.SeaHawkPaints.com

カタログの1ページ目を開く

Tuff Stuff High Build Epoxy Primer Surface Preparation Paint only clean, dry surfaces. Remove all grease, oil, wax, or other foreign material by solvent or detergent washing. (SSPC-SPI) Fiberglass: Soda Blast, Sand with 60-80 grit sandpaper, or equivalent. Once desired profile is achieved, wipe down with rags saturated with Sea Hawk Thinner 2044 to remove all the sanding dust. This procedure should be followed by at least 2-3 coats of Tuff Stuff for general purpose applications or use at least three coats for osmotic blistering prevention. For repair of osmotic gelcoat blistering please...

カタログの2ページ目を開く