カタログ >
International Marine >
Intersmooth 7465HS SPC

Intersmooth 7465HS SPC
1 / 4ページ

カタログの抜粋

Intersmooth 7465HS SPC TBT Free, Low Friction, Self Polishing Copolymer A/F PRODUCT DESCRIPTION A high solids, high performance, TBT free, self polishing copolymer (SPC) antifouling. Particularly suitable for use where solvent emissions need to be reduced. INTENDED USES Specifically designed for Deep Sea Vessels. For use at Newbuilding. PRODUCT INFORMATION BEA774-Brown, BEA777-Red BEA764-Brown, BEA767-Red (only available in European non-regulated countries) Part B (Curing Agent) Volume Solids Typical Film Thickness Range: 3 - 8 mils dry (5.6 - 14.8 mils wet) may be specified depending upon end use. Theoretical Coverage Range: 294 - 110 ft²/US gal at 3 - 8 mils dft, allow appropriate loss factors Airless Spray, Brush, Roller Flash Point Drying Information Before Flooding Note The above times to flooding apply to single coats applied at no more than 6 mils dft. Where multiple coats (or single coats above 6 mils dft) are applied in dock before launch, times to flooding must be increased as follows: 48 hours at 23° F, 36 hours at 41°F, 24 hours at 77°F, 12 hours at 95°F. Overcoating Data - see limitations REGULATORY DATA For overcoating at 23°F allow a minimum of 24 hours between coats for 3 coat systems. 425 g/lt (3.55 lb/US gal) as supplied (EPA Method 24) 226 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) 3.34 g/lt Chinese National Standard GB23985 Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. EPA This product is not registered in the USA or Canada. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:1/27/

カタログの1ページ目を開く

Intersmooth 7465HS SPC TBT Free, Low Friction, Self Polishing Copolymer A/F CERTIFICATION When used as part of an approved scheme, this product has the following certification: Product recognised by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • Bureau Veritas • DNV GL • Lloyds Register Consult your International Paint representative for details. Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use...

カタログの2ページ目を開く

Intersmooth 7465HS SPC TBT Free, Low Friction, Self Polishing Copolymer A/F APPLICATION Mixing This material is a one pack coating and should always be mixed thoroughly with a power agitator before application. International GTA007. Thinning is not normally required. Consult the local representative for advice during application in extreme conditions. Do not thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 21-31 thou (0.54-0.8 mm) Total output fluid pressure at spray tip not less than 2700 psi (190 kg/cm²) Conventional Spray Application by...

カタログの3ページ目を開く

Intersmooth 7465HS SPC TBT Free, Low Friction, Self Polishing Copolymer A/F LIMITATIONS Coating lifetime is directly proportional to thickness applied. Performance of the product is dependant upon the specified film thickness being achieved. On immersion, Intersmooth 7465HS SPC will exhibit a slight color change. Intersmooth 7465HS SPC may be applied at substrate temperatures down to 5°F. Before applications are made below 23°F consult your local IP representative for further detail of application procedure. Overcoating information is given for guidance only and is subject to regional...

カタログの4ページ目を開く