カタログ >
International Marine >
Intersleek 1100SR

Intersleek 1100SR
1 / 4ページ

カタログの抜粋

Intersleek 1100SR Advanced Fluoropolymer Foul Release Coating PRODUCT DESCRIPTION Advanced fluoropolymer foul release coating for the control of slime. INTENDED USES For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION FXA991-Grey, FXA992-Blue, FXA997-Red, FXA999-Black and a limited range of colors Part B (Curing Agent) Volume Solids 9 volume(s) Part A to 2 volume(s) Part B to 1 volume(s) Part C Typical Film Thickness Range: 6 - 8 mils dry (8.3 - 11.1 mils wet) may be specified depending upon end use. Theoretical Coverage Range: 196 - 147 ft²/US gal at 6 - 8 mils dft, allow appropriate loss factors Airless Spray, Brush Flash Point Part A 115°F; Part B 72°F; Part C 97°F; Mixed 91°F Induction Period Drying Information Before Flooding The interval prior to flooding may be reduced to 24 hours at temperatures between 41°F and 68°F provided that the ship remains at rest for a minimum period of 2-3 days after flooding. At temperatures between 32°F and 41°F, the absolute minimum time to flooding is 48 hours and the ship must remain at rest for a minimum of 4 days afterundocking. However, the coating may suffer intercoat detachment in any areas that are subject to mechanical abrasion due to, eg. fendering or impact damage. Overcoating Data - see limitations Substrate Temperature REGULATORY DATA May be overcoated by self, either when fresh or after prolonged immersion provided surface is in good, clean condition. Consult International Paint. 240 g/lt (2.00 lb/US gal) as supplied (EPA Method 24) 238 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) 2.10 g/lt Chinese National Standard GB23985 Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:10/3

カタログの1ページ目を開く

Intersleek 1100SR Advanced Fluoropolymer Foul Release Coating CERTIFICATION When used as part of an approved scheme, this product has the following certification: Product recognised by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • • • • Bureau Veritas DNV GL Lloyds Register Korean Register of Shipping Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces...

カタログの2ページ目を開く

Intersleek 1100SR Advanced Fluoropolymer Foul Release Coating APPLICATION Mixing Material is supplied in 3 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Part A with a power agitator. (2) Combine entire contents of Part A and Part B and mix thoroughly with a power agitator. (3) Add entire contents of Part C and mix thoroughly with a power agitator. Carefully add Part C (under slow power-mixing) into the Part A / Part B mix. These products are moisture sensitive and they should not be opened until just before they are needed. Not recommended. Use...

カタログの3ページ目を開く

Intersleek 1100SR Advanced Fluoropolymer Foul Release Coating LIMITATIONS Minimum acceptable substrate temperature at the time of application is 32°F. A minimum Relative Humidity of 30% is required to ensure satisfactory curing. Longer cure times will be required if the Relative Humidity falls below 30%. Care should be taken to avoid overspray onto other coated areas. Intersleek 1100SR must be applied over Intersleek 737 tie coat (Intersleek 731 tie coat in USA) within the required overcoating interval. All equipment must be thoroughly clean prior to use, and before re-use with other...

カタログの4ページ目を開く