Intergard 403
1 / 4ページ

カタログの抜粋

Intergard 403 Epoxy Anticorrosive PRODUCT DESCRIPTION A tar free, light coloured epoxy coating. INTENDED USES For use as a high performance anticorrosive in ballast tanks, underwater hull, cofferdams and void spaces. Suitable for use with controlled cathodic protection. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION KBA400-Buff, KBA402-Aluminium Grey, KBA404-Grey, KBA406-Light Red (KBA412- Aluminium Red, KBA413- Light Grey Available in Korea only) (KBA401-Off White available in North America only) (KBA411- Black Available in certain Asian locations only. Consult International Paint.) Part B (Curing Agent) Volume Solids 4 volume(s) Part A to 1 volume(s) Part B (In Korea, supplied as 3 volumes Part A to 1 volume Part B) Typical Film Thickness Theoretical Coverage 5.44 m²/litre at 125 microns dft, allow appropriate loss factors Airless Spray, Roller, Brush Flash Point (Typical) Part A 26°C; Part B 33°C; Mixed 27°C (Product produced and supplied in North America has flash points of Part A 43°C , Part B 39°C and Mixed 39°C respectively due to locally sourced solvents. There is no detrimental effect on product performance.) Induction Period 15 minutes at temperatures below 25°C Drying Information Overcoating Data - see limitations REGULATORY DATA Substrate Temperature 304 g/lt as supplied (EPA Method 24) 252 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) 261 g/lt Chinese National Standard GB23985 Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. MIL SPEC Marine Coatings Page 1 of 4 Issue Date:15/12/2015 Ref:423

カタログの1ページ目を開く

Intergard 403 Epoxy Anticorrosive CERTIFICATION When used as part of an approved scheme, this material has the following certification: • • • • • Fire Resistance - Surface Spread of Flame (Exova Warringtonfire) Fire Resistance - Smoke & Toxicity (Exova Warringtonfire) Food Contact - Carriage of Grain (NOHA) Tank Coatings - B1 Classification of Ballast Tank Coatings (DNV/Marintek tested) Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system...

カタログの2ページ目を開く

Intergard 403 Epoxy Anticorrosive APPLICATION Mixing Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. International GTA220. Thinning is not normally required. Consult the local representative for advice during application in extreme conditions. Do not thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.53-0.66 mm (21-26 thou) Total...

カタログの3ページ目を開く

Intergard 403 Epoxy Anticorrosive LIMITATIONS This product will not cure adequately below 5°C. For maximum performance ambient curing temperatures should be above 10°C. Drying times and overcoating intervals may alter due to on-site factors such as tank configuration or ventilation rates etc. Intergard 403 must not be used in mixed schemes with Intergard 423. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations....

カタログの4ページ目を開く