
カタログの抜粋

Hydroblasting Standards www.international-marine.com
カタログの1ページ目を開く
Hydroblasting Standards Contents 1. 2. 3. 4. Introduction Format Explanatory Text Procedure For Using The Standards 5. Notes 6. References 7. Visual Standards 1 Introduction Hydroblasting is a technique for cleaning surfaces, which relies entirely on the energy of water striking a surface to achieve its cleaning effect. Abrasives are NOT used in hydroblasting systems. Consequently the problems caused by dust pollution and by the disposal of spent abrasives are eliminated. Two different hydroblasting operating pressures are commonly encountered. • High pressure hydroblasting, operating at...
カタログの2ページ目を開く
The definitions are: Rust Grade C: Steel surface completely covered with rust but with little or slight pitting under normal vision. Rust Grade D: Steel surface completely covered with rust on which general pitting is visible under normal vision. 3.2 Blast Standards The standard illustrates grade C and D surfaces prepared by hydroblasting to two different degrees of cleanliness. These are designated HB2 and HB21/2 and are comparable to Sa2 and Sa21/2 described in the ISO 8501-1:1988 surface preparation standard and to SSPC-SP6 and SSPC-SP10 of the Steel Structures Painting Council surface...
カタログの3ページ目を開く
4.3 Compare the prepared surface with the photograph selected immediately after hydroblasting but before the surface has flash rusted to evaluate the degree of cleaning, see note 5.3. 4.4 Prior to painting compare the flash rusted surface with the flash rusting photographs. For example, D HB2 L, D HB2 M, D HB2 H to evaluate the degree of flash rusting that has occurred. 4.5 Check that the paint product specified is suitable for overcoating the degree of flash rusting that has occurred. See note 5.7. 5 Notes 5.1 Definition of Terms The terms hydroblasting, hydrojetting and water jetting...
カタログの4ページ目を開く
5.6 Chemical Corrosion Inhibition Flash rusting can be prevented by the use of water soluble chemical corrosion inhibitors. These inhibitors may leave a crystalline layer on the steel surface as the water evaporates which can then lead to a loss of adhesion and osmotic blistering if coatings are applied over this type of surface. International Paint do not recommend the use of corrosion inhibitors to hold wet blasted surfaces. If inhibitors are used, they must be thoroughly washed off with fresh water before International Paint products are applied. 5.7 Removal of Flash Rusting When flash...
カタログの5ページ目を開く
7 Visual Standards Rust Grade Standards Rust grade C Rust grade D
カタログの6ページ目を開く
Preparation Standard C HB2 Rust grade C C HB2 Rust grade C Hydroblasted to an Sa2 equivalent
カタログの7ページ目を開く
Degree of Flash Rusting C HB2 L. Light flash rusting C HB2 M. Moderate flash rusting C HB2 H. Heavy flash rusting
カタログの8ページ目を開く
Preparation Standard C HB2 1/2 Rust grade C C HB21/2 Rust grade C Hydroblasted to an Sa21/2 equivalent
カタログの9ページ目を開く
Degree of Flash Rusting C HB21/2 L. Light flash rusting C HB21/2 M. Moderate flash rusting C HB21/2 H. Heavy flash rusting
カタログの10ページ目を開く
Preparation Standard D HB2 Rust grade D D HB2 Rust grade D Hydroblasted to an Sa2 equivalent
カタログの11ページ目を開く
Degree of Flash Rusting D HB2 L. Light flash rusting D HB2 M. Moderate flash rusting D HB2 H. Heavy flash rusting
カタログの12ページ目を開く
Preparation Standard D HB2 1/2 Rust grade D D HB21/2 Rust grade D Hydroblasted to an Sa21/2 equivalent
カタログの13ページ目を開く
Degree of Flash Rusting D HB21/2 L. Light flash rusting D HB21/2 M. Moderate flash rusting D HB21/2 H. Heavy flash rusting
カタログの14ページ目を開く
September 2004 Argentina Australia Bahrain Belgium Brazil Bulgaria Canada Chile Colombia Croatia Cuba Cyprus Denmark Ecuador Egypt Estonia Fiji Finland France Germany Greece Hong Kong Iceland India Indonesia Iran Italy Japan Kuwait Latvia Lithuania Luxembourg Malaysia Malta Mexico Netherlands New Zealand Northern Ireland Norway Pakistan Panama Papua New Guinea Peoples Republic of China Peru Philippines Poland Portugal Qatar Republic of Ireland Romania Russia Saudi Arabia Singapore Slovenia South Africa South Korea Spain Sri Lanka Sweden Taiwan Thailand Turkey U.S.A. Ukraine United Arab...
カタログの15ページ目を開くInternational Marineのすべてのカタログとパンフレット
-
Intergard 5000
4 ページ
-
Interline 975P
4 ページ
-
Interline 994LT
4 ページ
-
Interline 644
4 ページ
-
Interspeed 5617
4 ページ
-
Intersmooth 7670 SPC
4 ページ
-
Interflex 8700 SPC
4 ページ
-
Interplate Zero
4 ページ
-
Intergard 269
4 ページ
-
Interline 850
4 ページ
-
Intersleek 1100SR
4 ページ
-
Intersleek 717
4 ページ
-
Interfine 878
4 ページ
-
Intershield 456
4 ページ
-
Intershield 851
4 ページ
-
Intershield 852
4 ページ
-
Intershield 803Plus
4 ページ
-
Intercept 7000
1 ページ
-
Interbond 808
2 ページ
-
Integard 5555 PIC
2 ページ
-
Intertrac Vision
4 ページ
-
Intersleek 1000
6 ページ
-
Intershield 5150LWT
2 ページ
-
Intershield 300
8 ページ
-
Interline 9001
6 ページ
-
Interflex 8700 PIC
2 ページ
-
Fisheries
2 ページ
-
Interline 904
2 ページ
-
Intershield 6GV
2 ページ
-
Intersleek 700
2 ページ
-
Interswift 6600
2 ページ
-
Interswift 6800HS
2 ページ
-
Intergard 5400 PIC
2 ページ
-
Interspeed-5640
2 ページ
-
Intershield 300V
4 ページ
-
Intergard 821
4 ページ
-
Intertherm 50
4 ページ
-
Intergard 403
4 ページ
-
Intersleek
6 ページ
-
Cargo Tank Coatings
7 ページ
-
Cargo Hold Coatings
7 ページ
-
Intercept 8000 LPP
4 ページ
-
Interswift 6900Si
4 ページ
-
Intergard 7500
2 ページ
-
Intergard 7020
2 ページ
-
Interline®9001
5 ページ
-
Interplate® Zero
11 ページ
-
Maintenance and Repair
19 ページ
-
Slurryblasting Standards
14 ページ
-
Cargo Hold
8 ページ
-
Abrasive Sweep Standards
12 ページ
-
Colour Card
2 ページ
-
Interprime 65
4 ページ
-
Interline 104
4 ページ
-
Intersleek 386
4 ページ
-
Intersleek 737
4 ページ
-
Intersleek 970
4 ページ
-
Intersmooth 360 SPC
4 ページ
-
Interspeed 6400
4 ページ
-
Interswift 655
4 ページ
-
Intertuf 362
4 ページ
-
Intersmooth 365 SPC
4 ページ
-
Interswift 455FB
4 ページ
-
INTERLAC 678
4 ページ
-
INTERGARD 400
4 ページ
-
INTERFINE 629HS
4 ページ
-
INTERTHANE 990
4 ページ
-
INTERBOND 501
4 ページ
-
INTERPRIME 198
4 ページ
-
BALLAST TANK BROCHURE
13 ページ
カタログアーカイブ
-
Intergard 343
9 ページ