カタログ >
Hubbell Marine Electrical Products >
Marine 12 Volt DC Switches

Marine 12 Volt DC Switches
1 / 2ページ

カタログの抜粋

Marine 12 Volt DC Switches Catalog Number • Secures power off • Prevents accidental activation of power circuits • Ideal for use with MPB11HD & MPB11M push button switches Battery Ignition Switch • 2 Position: Off / On • 10A @ 12V DC • Heavy duty brass construction • Mounts in panels up to 1” thick • Ideal ignition / starter replacement switch • Recommended for smaller boats Ignition / Starter Switch • 3 Position: Off, Ignition, Ignition & Start • 10A per circuit; 15A max. @ 12V DC • Heavy duty brass construction • Mounts in panels up to 1” thick • Same as MIS123 including accessory option • Ideal for accessory use without starting engine Ignition / Starter Switch • 4 Position: Accessory, Off, Ignition & Accessory, Ignition & Start • 10A per circuit; 15A max. at 12V DC • Heavy duty brass construction • Mount in panels up to 1” thick • General use switch, on / off switch • Recommended for inside cabin use • Ideal for manual control of an accessory, i.e. lights, bilge pump, blowers, etc. Push-Pull Switch • Two Position: Normally Off - Pull On • 10A @ 12V DC • Heavy duty brass construction • Mounts in panels up to 1” thick • Gasket sealed case enhances moisture resistance • Ideal for wipers Push-Pull Switch • Two Position: Normally Off - Pull On • 10A @ 12V DC • Heavy duty brass construction • Mounts in panels up to 3/4” thick • Ideal for on / off switch in weather exposed locations • 12” leads allow for easy wiring Push - Pull Switch • 2 Position: Normally Off - Pull On • 10A @ 12V DC • Heavy duty brass construction • Rear vinyl enclosure for added protection • Mounts in panels up to 5/8” thick • Ideal for operating anchor & running lights • One switch permits operations of two circuits independently: - Anchor and running lights - Dual bilge pump controls - Dual wipe speed control Push - Pull Switch • 3 Position: Off, On #1 or On #2 • 10A @ 12V DC • Heavy duty brass construction • Mounts in panels up to 1” thick Ignition Switches Push-Pull Switches Battery Selector & Disconnect Switches • Compact design with simple on / off control • Permits total shut down of electrical system MBDS1 Battery Disconnect Switch • 2 Position: Off - On • 175A Continuous - 800A Intermittent; 6-36V DC • Extra heavy duty brass construction • Face plate included • U.L. Listed • Ignition protected • Mounts in panels up to 15/16” thick • Permits control of independent or dual battery control • Master disconnect switch • Designed for your toughest applications • Surface or through panel mount (3 5/16” hole) MBDSS1 Dual Selector & Master Disconnect Switch • 4 Position: Off, Battery #1, Battery #2, Both • 310A Continuous - 500A intermittent; 6-36V DC • U.L. Listed and Coast Guard Approved • Ignition protected

カタログの1ページ目を開く

Catalog Number Push Button Switches • Recommended for in cabin use • Ideal for horns, momentary wiper control, etc. • Can be used with MIS11 ignition switch Momentary Switch • 2 Position: Off - Momentary On • 10A @ 12V DC • Heavy duty brass construction • Mounts in panels up to 1” thick • Recommended for use on bridge • Ideal for use with MIS11 battery ignition switch, for horns, momentary wiper control, etc. Momentary Switch • 2 Position: Off - Momentary On • 35A @ 12V DC • Extra heavy duty brass construction • Mounts in panels up to 1” thick • Same as MBP11HD with added moisture...

カタログの2ページ目を開く