カタログの抜粋
Full General Datasheet SPABOND™ 730 RAPID STRUCTURAL ADHESIVE ¬ Fast clamp time, high strength, structural adhesive Gels in 10 minutes, solid in 2 hours, Good degree of cure after 6 hours at ambient Available in 400ml 2 component dual cartridges INTRODUCTION Spabond™ 730 is a fast curing structural adhesive designed for applications where reduced clamp times are important. It has a simple 1:1 by weight and volume mix ratio. It can be used to bond together a wide variety of dissimilar materials and has been designed to give a durable high strength bond. Spabond™ 730 is available in cartridges.
カタログの1ページ目を開く
PRODUCT INFORMATION AVAILABILITY The product is available in a number of formats please contact your local customer support or download the latest product catalogue available on www.gurit.com. TRANSPORT & STORAGE COMPONENT UNITS 10 – 25°C The resin and hardeners should be kept in securely closed containers during transport and storage. Any accidental spillage should be soaked up with sand, sawdust, cotton Spabond™ 730 Resin months 12 waste or any other absorbent material. The area should then be washed clean (see Spabond™ 730 Hardener months 12 appropriate Safety Data Sheet). Adequate long...
カタログの2ページ目を開く
SPABOND™ 730 This 1 page product summary is intended for use in conjunction with further advice provided under the Instructions for Use section. All data has been generated from typical production material and does not constitute a product specification. MIXING AND HANDLING PROPERTY MIXED SYSTEM Appearance - colour TEST METHOD Appearance - form Thixotropic paste COMPONENT & MIXED SYSTEM VISCOSITY UNITS Spabond™ 730 Resin Viscosity Spabond™ 730 Hardener Viscosity Initial Mixed System Viscosity Clamp Time** TEST METHOD ADHESIVE PERFORMANCE MECHANICAL PROPERTIES TEST STANDARD CURED MECHANICAL...
カタログの3ページ目を開く
NOTICE All advice, instruction or recommendation is given in good faith but the selling Gurit entity (the Company) only warrants that advice in writing is given with reasonable skill and care. No further duty or responsibility is accepted by the Company. All advice is given subject to the terms and conditions of sale (the Conditions) which are available on request from the Company or may be viewed at Gurit’s Website: www.gurit.com/terms-and-conditions.aspx The Company strongly recommends that Customers make test panels in the final process conditions and conduct appropriate testing of any...
カタログの4ページ目を開くGuritのすべてのカタログとパンフレット
-
GURIT® BALSAFLEX™4 ページ
-
CORECELL™ S3 ページ
-
CORECELL™ T3 ページ
-
GURIT® PVC3 ページ
-
CORECELL™ A3 ページ
-
SPABOND™ 3457 ページ
-
T-Prime 1608 ページ
-
T-Prime 130-1 (v5)8 ページ
-
SMARTCURE™ (v9)4 ページ
-
T-Lam 130-1 Slow6 ページ
-
T-Gel 130-16 ページ
-
T-Paste 70-26 ページ
-
CR 34005 ページ
-
Gurit® Kerdyn® Green4 ページ
-
Aerospace2 ページ
-
PB10004 ページ
-
HI-PANEL2 ページ
-
Gurit G-PET1 ページ
-
Eposeal 3006 ページ
-
Ampreg 268 ページ
-
Ampreg 21FR6 ページ
-
ST 956 ページ
-
PREPREGS11 ページ
-
CORE MATERIALS9 ページ
-
ADHESIVES5 ページ
-
WE91 - 24 ページ
-
WE91 - 14 ページ
-
SE 85 GT5 ページ
-
SE 855 ページ
-
SE 84 Nano5 ページ
-
PH 8404 ページ
-
PN 9014 ページ
-
SE 3004 ページ
-
SC 1104 ページ
-
SE 2005 ページ
-
ST 164 ページ
-
SE 84LV6 ページ
-
ST 706 ページ
-
SE 705 ページ
-
SPABOND 340LV HT6 ページ
-
SPABOND 3454 ページ
-
SPABOND 3407 ページ
-
SPABOND 340LV6 ページ
