UniXact Automated Dispensing Solutions
1 / 64ページ

UniXact® Automated Dispense Platform For automated, programmable, precision micro-dispensing. For professional use only. Not approved for use in explosive atmospheres or hazardous locations. Models: C-300 C-500 Important Safety Instructions Read all warnings and instructions in this manual and in the UniXact Automated Dispense Platform Setup and Operation manual 3A3649. Save all instructions. PROVEN QUALITY. LEADING TECHNOLOGY.

Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C-300 and C-500 Base Systems . . . . . . . . . . . . 4 C-300 Module Base, 25C202 . . . . . . . . . . . . . . . 9 C-500 Module Base, 25C273 . . . . . . . . . . . . . . 14 Axis Z Actuators, 25C275, 25C276 . . . . . . . . . . 19 Mounting Module No Z Axis, 25C066 . . . . . . . . 21 Valve Holders . . . . . . . . . . . . . . . . . . . . . . . . . . 22 C-300...

NOTE: See manual 3A3649 for related valve and supply system manuals.

Parts C-300 and C-500 Base Systems Model C-300 Shown (with front access panel removed to view electronics)

FIG. 2: C-300 and C-500 System Parts 2 (with Cover Removed)

10 FIG. 3: C-300 and C-500 System Parts 3 (Rear View)

25C202 MODULE, base, xy, c300 25C273 MODULE, base, xy, c500

25C351 MODULE, bundle, cable, z, pd, c3 1 25C352 MODULE, bundle, cable, z, 1053, c3 1 25C353 MODULE, bundle, cable, z, pc, c3 1 25C354 MODULE, bundle, cable, z, 1206, c3 1 25C356 MODULE, bundle, cable, z, adv, c3 1 25C358 MODULE, bundle, cable, z, end, c3 1 25C359 MODULE, bundle, cable, z, pd, c5 1 25C360 MODULE, bundle, cable, z, 1053, c5 1 25C361 MODULE, bundle, cable, z, pc, c5 1 25C362 MODULE, bundle, cable, z, 1206, c5 1 25C388 MODULE, bundle, cable, adv, c5 1 25C399 MODULE,...

Affix Velcro tape to the unlabeled side of the power pack supplied with the control computer (agency markings and part information should be visible) and secure it to the location shown. Snug bolt, then tighten 1/4 turn. Apply thread sealant. FIG. 4: Module Base 25C202 Front View

FIG. 5: Rear View of Gantry Table Looking into Machine from Above FIG. 6: View from Above with Top Panel Removed 10

Description FRAME, base, xyz ADJUSTER, levlr, stem, 3/4-10,2.00lg PLATE, cover, painted SCREW, mach, pnh GUARD, trim, edge BUSHING, wire protector, snap-in BUSHING, wire protector, 1 3/8 od BUSHING, wire protector, snap-in HOLDER, anchor, wire tie, nylon MODULE, ac pwr, filter, xyz WASHER, lock, 3/8

25C203 MODULE, panel, elec, xyz, c300 1 123396 NUT, flange, serrated, 3/8-16 4 17J448 HARNESS, motion table,motor, y 1 F0450047G GUARD, fan, wire, use with f045004 1 108018 SCREW, mach, fill hd 4 17E197 HARNESS, motion table, power, y 1 17G028 BRACKET, mtg, igus, x-axis, painted 1 127047 SCREW, mach, hex, flange, m6 x 1 x 10 mm 4 17L960 BRACKET, angle, sensor, barrel y 1 25A834 KIT, motor, servo, x/y axis 2 17F840 PAD, damping, actuator, .375 thk 4 127048 SCREW, mach, hex, flange, m10 x 1.5 x 2 4 25C204 MODULE, cable, track,...

A Replacement Danger and Warning labels, tags, and cards are available at no cost.

Affix Velcro tape to the unlabeled side of the power pack supplied with the electrical panel (agency markings and part information should be visible) and secure it to the location shown. Apply thread sealant. Snug bolt, then tighten 1/4 turn. FIG. 8: Module Base 25C273 Front View

FIG. 9: Rear View of Gantry Table

FIG. 10: Module Base 25C273 Rear View

103A 123424 GUARD, trim, edge 1.6 ft 130A 17L960 BRACKET, angle, sensor, barrel y 1

153A 17E386 HARNESS, motion table, mute y, front 1 A Replacement Danger and Warning labels, tags, and cards are available at no cost.

Axis Z Actuators, 25C275, 25C276 Ref Part 17E321 201 25A430 202 128317 Description MODULE, axis, z, 75 mm MODULE, axis z, COUPLING, motor, isel BLOCK, motor mounting HOLDER, anchor, wire tie, nylon SCREW, mach, pnh BRAKE, motor, z axis SCREW, cap, sch KIT, motor, servo, z/theta axis SCREW, shsc, m6-1.0 x 30, sst PLUG, hole, 1.375 in. dia, blk BRACKET, cable track

SCREW, cap, sch (m6 x 8) NUT, tee, m6 SCREW, cap, sch, hex PLATE, mtg, z axis SCREW, cap skt hd m6 x 20 m BRACKET, connector mtg, z-axis COVER, cable bulkhead CONNECTOR, thru, m12, mxf, reverse key CONNECTOR, thru, m12, mxf CONNECTOR, thru, m8, mxf BULKHEAD, 1/4 t x 1/4 t MODULE, gca, z-axis FASTENER, screw, shcs, m3 x.5 x 10, ss STRAP, tie HARNESS, motion table, power, z HARNESS, motion table, motor, z

Mounting Module No Z Axis, 25C066 Ref Part Description PLATE, mounting valve, no-z-axis BRACKET, cable track, no z SCREW, mach, hex, flange, m6 x 1 x 10 mm SCREW, cap, sch, hex SCREW, mach, pnh BRACKET, connector mtg, z-axis COVER, cable bulkhead CONNECTOR, thru, m12, mxf, reverse key CONNECTOR, thru, m12, mxf CONNECTOR, thru, m8, mxf BULKHEAD, 1/4 t x 1/4 t MODULE, gca, z-axis FASTENER, screw, shcs, m3 x.5 x 10, ss HARNESS, wire, pwr, dt2, no theta HARNESS, e-stop, xyz, disp, mc1 ❖ Not shown here. Refer to Appendix A - Wiring Reference on page 57.

Valve Holders 1093 Valve Holder, 25C459, and 1053 Valve Holder, 25C174 1 Apply thread sealant. Valve shown for mounting purposes only. Valve shown for mounting purposes only. FIG. 13: 1093 Valve Holder and 1053 Valve Holder

Description SCREW, shcs m5 x 16 SCREW, cap, socket hd, m3 FITTING, connector, 1/4 tub x 1/8 npt, b SCREW, shsc, m6-1.0 x 30, sst VALVE, direct solenoid SCREW, shcs BRACKET, disconnect, 1053 PLATE, mounting, 1053_automation BRACKET, solenoid, 1053, automation MUFFLER, sintered, dia 1/8 PLATE, adjust, mtg, 1053 KIT, motor, servo, z/theta axis SCREW, flat head, steel, m2.5 x 10 SCREW, cap, socket hd SCREW, cap, socket hd SCREW, shcs, m4 x 10, lp head BRACKET, xz mute sensor SENSOR, retro, reflective RELAY, contactor, 24v dc, 4 RELAY, 24v dc coil, spdt, 6a/240v HARNESS, wire, cb4, mc2 HARNESS,...