Indy-X User Manual
1 / 44ページ

DISPENSING EXCELLENCE Indy-X Chop DISPENSING EXCELLENCE INDIANAPOLIS, INDIANA Email gcisales@glascraft.com

Parts & Illustrations

About This Manual Before operating, maintaining or servicing any GlasCraft system, read and understand all of the technical and safety literature provided with GlasCraft products. If you do not have the prop- er or related manuals and safety literature for your GlasCraft system, contact your GlasCraft In this GlasCraft technical and safety publica- tion, the following advisories will be provided Is information about the procedure in progress. Is imperative information about equipment Is imperative information about personal safety. The information in this document is intended only to...

Parts & Illustrations MODEL 23575-00 INDY-X CHOP DISPENSE GUN Impingement Dispense Tips (see pages 3 & 4) The J5 tip is furnished with the Spray Gun. For more information, contact your distributor, or GlasCraft Service Department. Material Airless Spray Tip Options: (see page 5) Repair Parts Kits:

Indy-X Chop Impingement Dispense Tip Reference Chart

Indy-X Chop Impingement Dispense Tip Reference Chart series spray tips.

Indy-X Chop Airless Dispense Tip Reference Chart series spray tips.

23575-00 Indy-X Chop Dispense Gun 1) Catalyst seat assembly p/n: 23544-00 / 2) Material seat assembly p/n: E-135 % ^ v , 3) Material needle valve assembly p/n: 23545-00 REVISON B

23575-00 Indy-X Chop Dispense Gun

23575-00 Indy-X Chop Dispense Gun

23575-00 Indy-X Chop Dispense Gun series spray tips.

23575-00 Indy-X Chop Dispense Gun

23575-00 Indy-X Chop Dispense Gun

23575-00 Indy-X Chop Dispense Gun

Operating Your Polyester System Any tool, if used improperly, can be dangerous. Safety is ultimately the responsibility of those using the tool. In like manner, safe operation of polyes- ter processes is the responsibility of those who use such processes and those who operate the equip- ment. This manual outlines procedures to be fol- lowed in conducting polyester operations safely. This system has been specifically designed for use of Polyester Resin ,Gel-Coat ,and Methyl Ethyl Ke- tone Peroxides (MEKP) applications. Other formu- lations or blends considered for use in this equip- ment is...

GlasCraft recommends that the user consult the state and local regulations established for all Safety equip- ment listed. 2.1 Hazards Associated with Laminating Operations The major hazards which should be guarded against in polyester laminating operations are those associated 1. The flammability and explosion dangers of the catalyst normally used - Methyl Ethyl Ketone Peroxide (MEKP). 2. The flammability dangers of clean-up solvents sometimes used (GlasCraft recommends that clean-up solvents be nonflammable), and of resin diluents used, such as styrene. 3. The flammability dangers of...

Safety in handling MEKP depends to a great extent on employee education, proper safety instructions and safe use of the chemicals and equipment. Workers should be thoroughly informed of the hazards that may result from improper handling of MEKP, especially in regards to contamination, heat, friction and impact. They should be thoroughly instructed regarding the proper action to be taken in the storage, use and disposal of MEKP and other hazardous materials used in the laminating In addition, users should make every effort to: with copious quantities of clean water and disposed of in...

The reaction is unpredictable. Prior use of an HHC sol- vent without incident (corrosion or explosion) does NOT mean that such use is safe. These solvents can be dan- gerous alone (as a clean-up or flushing agent) or when used as a component or a coating material. There is no known inhibitor that is effective under all circumstances. Furthermore, the mixing of HHC solvents with other materials or solvents, such as MEK, alcohol, and tolu- ene, may render the inhibitors ineffective. The use of reclaimed solvents is particularly hazardous. Reclaimers may not add any inhibitors. Also, the pos-...

In your main plant, store only enough resin for one day's "NO SMOKING" signs must be posted and observed in all areas where resin is stored and/or used. Referto OSHA Section 1910.94, 1910.106, 1910.107 and consult resin suppliers for more detailed informa- Adequate ventilation (as covered in OSHA Section 1910.94 and NFPA No. 91) is important wherever sol- vents are stored or used, to minimize, confine and ex- haust the solvent vapors. Resin must never be stored in an area where MEKP is Open-top drums should not be used, due to possible contamination and possible catalyzation from overspray...

Contact a doctor immediately in the event of any in- jury and give him the information you have collected. If your information includes first aid instructions, ad- minister first aid immediately while you are contact- Fast treatment of the outer skin and eyes that con- tact such chemicals generally includes immediate and thorough washing of the exposed skin and im- mediate and continuous flushing of the eyes with lots of clean water for at least 15 minutes or more. These general instructions of first aid treatment, however, may be incorrect for some chemicals; that is why you must know the...

3.2 General Safety Precautions The following general safety precautions should be followed when servicing or operating this equip ment to ensure operator safety: When filling catalyst container, protective eye equipment must be worn to protect against Always maintain adequate material levels to prevent loss of prime during system operation. At the first sign of a leak, stop operations, acti- vate emergency stop valve, back off air regula- tors and open all bleed valves to remove all pressure from the gun, hoses, pump, catalyst system and any other liquid containers. Solvent Pot Pressure...

Grounding an object means providing an adequate path for the flow of an electrical charge from the ob- ject to the ground. An adequate path is one that per- mits charge to flow from the object fast enough that it will not accumulate to the extent that a spark can be formed. It is not possible to define exactly what will be an adequate path under all conditions since it depends on many variables. In any event, the grounding means should have the lowest possible electrical resistance. Grounding straps should be installed on all loose conductive objects in the spraying area. This includes...