End carriages
1 / 8ページ

カタログの抜粋

END CARRIAGES CRANE COMPONENTS

WHEEL SELECTION CHART * SINGLE GIRDER 4200 DOUBLE GIRDER * Given information is approximate. Final wheel diameter depends on speed, duty and rail width. LONG TRAVEL COMPONENTS STANDARD END CARRIAGES Speed Speeds Wheel base (00 for types S, T, A) S: Welded A: Articulated M: Single girder B: Double girder CB: Wheel head BG: Boogie TA: End carriage TS: Underslung end carriage Possible speeds in m/min. Possible speeds in m/min. High speed Precission speed 1/4 Useful rail width

カタログの2ページ目を開く

TRAVEL GEAREDMOTORS Gradual acceleration, smooth brakes, all with minimum noise. Specially designed by GH for use on cross travel and long travel motions. Travel wheels with double flanges with mounted bearings. Drive to the wheels is direct via splined shaft. THREE STAGE MOTOR-GEARBOXES L3 Motor type Gearbox type FOUR STAGE MOTOR-GEARBOXES D Motor type

カタログの3ページ目を開く

END CARRIAGES FOR SINGLE AND DOUBLE GIRDER CRANES 200 (Minimum dimension) Double Girder Single Girder Single Girder Double Girder * Dimension "B" corresponds to the measurement of the base of the girder. ** Dimension A14 corresponds to the span of the trolley. 200 (Minimum dimension) Single Girder * Dimension "B" corresponds to the measurement of the base of the girder. ** Dimension A14 corresponds to the span of the trolley. GH CRANES & COMPONENTS Double Girder Single Girder Double Girder

カタログの4ページ目を開く

END CARRIAGES FOR DOUBLE GIRDER CRANES A2 (Minimum dimension) * Dimension "B" corresponds to the measurement of the base of the girder. ** Dimension A14 corresponds to the span of the trolley. (Minimum dimension) * Dimension "B" corresponds to the measurement of the base of the girder. ** Dimension A14 corresponds to the span of the trolley.

カタログの5ページ目を開く

END CARRIAGES FOR UNDERSLUNG CRANES A2 A1 SINGLE GIRDER MODEL TS - M Average admissible wheel load per 2 wheels (daN) Note: End carriages with dimension A1 less than 2100 are only available as loose item. DOUBLE GIRDER MODEL TS - B Average admissible wheel load per 2 wheels (daN) Note: End carriages with dimension A1 less than 2100 are only available as loose item. Weld-on wheel head Ø160 Welded wheel-head Weld-on wheel head Ø 630

カタログの6ページ目を開く

WHEEL HEADS FOR GANTRY CRANES Maximum admissible wheel loads GGG70 (daN) Acc. with FEM/UNE M4 group Ø Wheel Gearbox type Cross travel speed in m/min Loads for ratio Rmin / Rmax = 0.35 Rolling track minimum quality S355 (St52) BOOGIES FOR GANTRY CRANES Dimensions Rail Type Burbach rail: Curved rail wheel head: Square rail:

カタログの7ページ目を開く

Hoist limit switch. Load limit device. Pendant plug-in connector. Cross travel limit switch actuator. Supports for cross travel and pendant power feed systems. Motor plug-in connectors. Towing arm. Cross travel limit switch. Long travel limit switch. Long travel limit switch actuator. Current collector arm. Festoon cable protection supports. 13. Cable clips. 14. Profile connection. 15. Sliding support. 16. End limit. 17. Cable trolleys. 18. Remote control. 19. Girder support. 20. Profile support. 21. Long travel cabinet. 21A. Hoist cabinet. 22. Ladder support. 23. Trolley rail. 6 7 Sede...

カタログの8ページ目を開く