436MMX
1 / 6ページ

Multi Module The E-PLEX 436MMX series is a 10 channel DC power distribution module. Eight channels are intended for lighting/resistive loads handling up to 8 amps each. Two channels incorporate diodes to allow for driving inductive loads and are capable of loads up to 15 amps each. The entire module is rated at 60 amps max. All channels have built in dimming providing a flexible solution for lighting without requiring additional external dimming hardware. The 436MMX incorporates thermal, short circuit, and programmable overload protection in order to safeguard the module against very rare or severe conditions. When E-Plex is not present, local electronic overrides capabilities allow independent operation of the device loads which can be used for testing and verification during installation. Design Specifications 10 channels of PWM dimming (60 amps total) 8 channels of 8 amp lighting / resistive loads 2 channels with 15 amp capability for inductive loads Status LED's for each channel Thermal, short circuit, and programmable overload Local electronic override capabilities Reverse battery protected Shock : Mil Std 202 Method 213 test condition 1 Vibration : Tested to Lloyds Register Approval Vibration Transient voltage suppression : EN6100-6-1 Power distribution: UL 1077 compliant (except high- voltage dielectric test) Ignition protection: UL 1500 compliant Salt spray: Tested to Lloyds Register Approval Salt Spray Operating Humidity: 0% to 100% (condensing) Powering systems - Empowering designers

Electrical Specifications Trip Speed Characteristics 7. De-rate max current by 0.2 A per °C above ambient, 25°C 2. Measured at 8.3 ms single half sine wave. (JEDEC Method) 3. Duty cycle at 1 minute on time, 5 minutes off. Trip delay must 4. Single pulse only. 6. PWM not recommended for motor loads unless factory 7. For load resistance greater than 2 ohms load inductance is 8. Specified as 50 feet of2AWG (43 mm2) wires with a 6 inch diameter spool for both power and ground. 9. For a channel configured as an input this specifies the turn-on/ 10.100 feet maximum wiring from battery. 11.Can...

Wiring Specifications Solid State Output 7 Solid State Output 6 Solid State Output 5 Solid State Output 4 Channels 5&6: 0 to 15A, 7-32VDC (Inductive Loads) All outputs are PWM capable and may be used to dim lighting loads Status LEDs: ON - Channels 1-10 indicates Load ON, E-Plex channel indicates module responding OFF - Channels 1-10 indicates Load OFF, E-Plex channel indicates module not responding 10 BLINKING - Channels 1-10 indicates Load FAULT, E-Plex channel indicates module responding. Pressing channel select in Manual Mode, LED will blink when channel is active. Power / Battery...

Typical Wiring Diagram Channels Select Status LEDs, Fuse / Disconnect ABYC / RVIA Battery Power Battery Return 11. Manual override switches are meant to be used as a local electronic manual override for emergency situations only. 12. Load activation function for switches 1 thru 6 are defined in E-Logic as either toggle or momentary operation. Powering systems - Empowering designers

Mechanical Specifications Screw assembly to a flat mounting surface in 2 places, as shown in the illustration. Mechanical Specifications Imperial (English) fasteners: Use #10 size screw, split lock washer, #10 washer. Torque to 20-22 ii Do not exceed this torque as it could cause dam; Metric fasteners: Use M5 size screw, M5 split loc washer and M5 washer. Torque to 250-280 N-cn Do not exceed this torque as it could cause dam; Mechanical Specifications J1 - Brown: Mates to Delphi P/N 15317308 J2 - Blue: Mates to Delphi P/N 15317304 Cavity Plug: Power Stud Connections: M5 nickel plated brass...

436MMX Series BATTERY 325QMM, 366HMM, 422QMM & 436MMX : 4, 6 or 10 channel multi-modules for control of lighting, including dimming and user-defined “mood” lighting POWER INVERTER 400ECM, 450ECM & 500CCM : Electronic control modules (“clocks”) that function as the master controller and programmer of the entire E-Plex system 361SIM : Inverter interface for complete control over your inverter functions 345LCD, 350LCD & 452LCD : 5.7”, 10” & 12” color LCD touchscreen displays that allow the user to interface with the E-Plex system, including monitoring and control functionality and includes...