Hullgard Extra Epoxy Primer
1 / 2ページ

カタログの抜粋

Hullgard Extra Epoxy Primer - 1

Product Data Sheet Hullgard Extra Epoxy Primer D6120/D3730 Intended Uses Hullgard Extra Primer is a two component epoxy substrate primer with excellent anticorrosive properties. It offers excellent aged recoatability and provides a perfect base for subsequent fairing with Awlfair fairing compound. Specification Data Volume Solids Specific Gravity Available Packs Base Converter Reducer Equipment Cleaning 46% 1.37 1 US Quart, 1 US Gallon, 5 US Gallon (EU only) D6120 Base D3730 Converter T0006 T0002, T0006 Theoretical Coverage Application Methods Theoretical Coverage Per Coat (at recommended DFT) Airless Spray, Conventional Spray Brush, Roller Multiple coats may be required when using roller or brush. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, thinning, application techniques, part size and application environment. VOC All VOC information contained herein is theoretical (unless otherwise stated). Actual VOC content may vary by batch from one color to another and when tested via standard test methodology. Product As Supplied (without reducer) g/L Hullgard Extra Epoxy Primer Surface Preparation The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation. Hullgard Extra may be directly applied to grit blasted steel in accordance with SSPCSP10 to a 23 mil (5075 micron) profile (or Sa2 ½ outside of the US). Alternatively power grind with a 24-36 grit disc to obtain profile. May also be applied to abraded aluminium (36 grit disc) and fibreglass (degrease and abrade using 180 grit paper). For the ultimate anticorrosive system first apply a coat of Max Cor CF to the suitably prepared steel or aluminium substrate (refer to Max Cor CF datasheet for further information on surface preparation and overcoating times). Wood should be clean and sanded with 80-180 grit paper. Mixing & Reduction Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. Application Methods Airless Spray, Conventional Spray, Brush, Roller Recommended Thinning Spraying Viscosity Check for settling, then thoroughly mix the base until a consistent homogenous blend is obtained. Power mixers or shakers are preferred. If not available thorough hand mixing is acceptable. Add converter and thoroughly mix again. Mix ratio by volume is 10 parts D6120 to 1.5 parts D3730. Reduction is not normally required but at lower temperatures small amounts (5%) of T0006 can be added. Do not reduce more than 15%. Application Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary. Airless spray is the most efficient way to apply this product. Roller application of Hullgard Extra Epoxy Primer direct to metal should be avoided due to the risk of snagging fibers. Do not apply paint materials to surfaces less than 3°C (5°F) above dew point, or to surfaces warmer than 41°C (105°F). Ambient temperature should be minimum 13°C (55°F) and maximum 41°C (105°F). Please refer to your local representative or visit www.international-yachtpaint.com for further information. Awlgrip, the AkzoNobel logo and other products mentioned in this publication are trademarks of AkzoNobel. ©AkzoNobel 2024 1 of 2 Ref:3502 Hullgard Extra Epoxy Primer Recoatability & Drying Times The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings.

カタログの1ページ目を開く
Hullgard Extra Epoxy Primer - 2

Application Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary. Product Data Sheet Airless spray is theEpoxy most efficient way to apply this product. Hullgard Extra Primer D6120/D3730 Roller application of Hullgard Extra Epoxy Primer direct to metal should be avoided due to the risk of snagging fibers. Do...

カタログの2ページ目を開く

Awlgripのすべてのカタログとパンフレット

  1. Max Cor CF Primer

    2 ページ

  2. 545

    2 ページ

  3. AWLBRITRE

    2 ページ

  4. Awlcare

    2 ページ

  5. Awlcraft SE

    3 ページ

  6. AWL®COAT TPC

    2 ページ

  7. Wash Primer CF

    2 ページ

  8. Satin Matt

    3 ページ

  9. Griptex

    3 ページ

  10. Awlgrip Topcoat

    2 ページ

  11. Crater-X

    2 ページ

  12. Awlfair LW

    3 ページ

  13. Awlfair Pumpable

    2 ページ

  14. Surface Cleaner

    2 ページ

  15. D3200 D6200

    4 ページ

  16. Awlfair LW Fast US

    2 ページ

  17. Awlcoat TPC

    2 ページ

  18. Alumiprep 33

    1 ページ

  19. Awlwood

    5 ページ

  20. Awlcare

    2 ページ

  21. Awlwash

    2 ページ

  22. Awlfair LW fast EU

    2 ページ

  23. 345 HS PRIMER

    3 ページ

  24. 321 HS UNDERCOAT

    3 ページ

  25. Awlcraft SE

    3 ページ

  26. Activators

    2 ページ

  27. 345HS Primer

    3 ページ

  28. Awlcraft 2000 VOC

    2 ページ

  29. Pro-Cure

    2 ページ

  30. REDUCERS

    3 ページ

  31. Awlbrite Quick-Fil

    2 ページ

カタログアーカイブ

  1. AWL®COAT TPC

    2 ページ

  2. AWLGRIP

    6 ページ

  3. CF 2K

    3 ページ