Awlfair LW Fairing Compound D8200 / D7200
1 / 5ページ

カタログの抜粋

Awlfair LW Fairing Compound D8200 / D7200 - 1

Product Data Sheet Awlfair LW Fairing Compound D8200 / D7200 Uses Fairing compounds are used to produce a smooth surface (and to reduce drag). Awlfair ® LW is designed for fairing, leveling or smoothing surface imperfections due to gouges, pitting, dents or weld seams. Awlfair® LW can be used above and below the waterline. Although designed as a cosmetic material the design of the structure it is being applied to should not be ignored. Seek independent expert advice to ensure that the construction and design are suitable for the chosen system and will not cause the fairing material to crack or delaminate Specification Data Packaging: Available in 1 Quart, 1 Gallon (US only) , 2 Gallon , 5 Gallon , 60LT (EU only) and 200lt (EU only). Theoretical Coverage: Application Method Longboard battens / Trowels / Spatulas / Putty Knifes Theoretical Coverage Per Coat * A max DFT of 5 - 6 mm per application is recommended to minimize air entrapment. Thicker applications may lead to excessive air entrapment which in turn can lead to defects and a system failure. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Awlfair LW Fairing Compound

カタログの1ページ目を開く
Awlfair LW Fairing Compound D8200 / D7200 - 2

Product Data Sheet Awlfair LW Fairing Compound D8200 / D7200 Mechanical Properties Temperature Compressive Strain (%) Tensile Strain (%) Flexural Strain (%) Flexural Modulus (MPa) Thermal Expansion Coefficient (x10-5) Warning: The information set out above is provided for guidance only and is based on our own internal product testing under controlled conditions using hand-mixed product. Please note that there may be slight variations when the product is used in service conditions. Air pockets due to poor application will significantly affect the mechanical properties of the Awlfair® LW and...

カタログの2ページ目を開く
Awlfair LW Fairing Compound D8200 / D7200 - 3

Product Data Sheet Awlfair LW Fairing Compound D8200 / D7200 Surface Preparation The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment age and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation. Only apply over properly applied and prepared Awlgrip primers. Hullgard Extra Epoxy Primer and High Build (GRP only) are recommended substrate primers. Awlfair® LW may be applied direct to Hullgard Extra without the need for...

カタログの3ページ目を開く
Awlfair LW Fairing Compound D8200 / D7200 - 4

Product Data Sheet Awlfair LW Fairing Compound D8200 / D7200 Recoatability and Drying Time The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure consult local technical service representative before proceeding. Drying times: Note: (While the fairing compound may appear hard dry, curing will continue for several days. This does not prevent overcoating) Drying Hardness Development (Shore D) Pot life Anticipated Cure Time at 75ºF/25°C/50% R.H: 8 hours touch dry; 24 hours resistance to...

カタログの4ページ目を開く
Awlfair LW Fairing Compound D8200 / D7200 - 5

Product Data Sheet Awlfair LW Fairing Compound D8200 / D7200 Pot life and working time is dependent upon temperature. Warmer climates will decrease pot life. Note: Awlfair® LW must be sealed with Hullgard Epoxy Primer (D6070/D3707) when used below the waterline. Note: Awlfair® LW should be sealed with an Awlgrip Epoxy Primer such as High Build or Ultra Build when used above the waterline. This will maximize gloss and color holdout in the Awlgrip top coat system. The Awlgrip Surfacing Filler may be used on top of the Awlfair® LW to cover pinholes and sand marks prior to priming. Sanding:...

カタログの5ページ目を開く

Awlgripのすべてのカタログとパンフレット

  1. Max Cor CF Primer

    2 ページ

  2. 545

    2 ページ

  3. AWLBRITRE

    2 ページ

  4. Awlcare

    2 ページ

  5. Awlcraft SE

    3 ページ

  6. AWL®COAT TPC

    2 ページ

  7. Wash Primer CF

    2 ページ

  8. Satin Matt

    3 ページ

  9. Griptex

    3 ページ

  10. Awlgrip Topcoat

    2 ページ

  11. Crater-X

    2 ページ

  12. Awlfair LW

    3 ページ

  13. Awlfair Pumpable

    2 ページ

  14. Surface Cleaner

    2 ページ

  15. D3200 D6200

    4 ページ

  16. Awlfair LW Fast US

    2 ページ

  17. Awlcoat TPC

    2 ページ

  18. Alumiprep 33

    1 ページ

  19. Awlwood

    5 ページ

  20. Awlcare

    2 ページ

  21. Awlwash

    2 ページ

  22. Awlfair LW fast EU

    2 ページ

  23. 345 HS PRIMER

    3 ページ

  24. 321 HS UNDERCOAT

    3 ページ

  25. Awlcraft SE

    3 ページ

  26. Activators

    2 ページ

  27. 345HS Primer

    3 ページ

  28. Awlcraft 2000 VOC

    2 ページ

  29. Pro-Cure

    2 ページ

  30. REDUCERS

    3 ページ

  31. Awlbrite Quick-Fil

    2 ページ

カタログアーカイブ

  1. AWL®COAT TPC

    2 ページ

  2. AWLGRIP

    6 ページ

  3. CF 2K

    3 ページ