AWLCRAFT 2000 METALLICS
1 / 3ページ

カタログの抜粋

AWLCRAFT 2000 METALLICS - 1

PRODUCT DATA SHEET AWLCRAFT 2000 METALLICS Features & Uses AWLCRAFT® 2000 Metallics are mixed the same way as conventional AWLCRAFT 2000 topcoats. Through the use of flow stabilizers, metallic flake float has been drastically reduced, and color consistency is improved. These new formulas will allow applicators to quickly and easily apply metallics for a finish with outstanding color, brilliance and luster. AWLCRAFT 2000 metallic flakes are pre-mixed into the pigmented color base which is applied in the same way as conventional pigmented AWLCRAFT 2000 topcoats. Notes:- Metallic topcoats must be applied over the appropriate Awlgrip primer or Awlcraft 2000 topcoat that has cured 12-24 hours and has been sanded until all gloss is removed. - (Optional) Metallics may be clear coated when applied as a base coat/clear coat application. - For use on smaller areas ONLY (such as stripes or parts). For larger area applications, we recommend Awlcraft SE. Contact your Awlgrip Technical Sales Representative for additional information. Specification Data Type: Two Component Acrylic Urethane Metallic Color: See color card and/or your Awlmix distributor Packaging: Available in 1 Gallon and 1 Quart containers (EU: 1 Gallon containers only) Theoretical Coverage: Sq. Ft./Gallon 512 Sq. Feet (48m 2) at one mil dry (25 microns) 171-256 Sq. Feet (16-24m2) at recommended dry film thickness. Calculated for mixed base and converter, reduced 25%. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 6-9 mils (150-225 microns) total of 3 or more coats. Recommended Dry Film Thickness: 2-3 mils (50-75 microns) total of 3 or more coats. Anticipated Cure Time at 77°F, 50% R.H: 24 Hours to tape free; 3 days to light service; 14 days for full cure. Recoatability: Spray applications consist of 3 coats applied over 2-4 hours. Exact time will vary with temperature, project size, and film thickness applied. AWLCRAFT 2000 clear coat can be applied after 12 hours at 77°F (25°C) but before 24 hours of cure. The last coat of metallic should be dry to touch to prevent mottling of the metallic. If sanding is desired, apply 2 coats of AWLCRAFT 2000 Clear (F3029) and allow curing over night before sanding. AWLCRAFT 2000 Metallics which have been allowed to cure more than 24 hours must be sanded and recoated with AWLCRAFT 2000 Metallic before recoating with F3029 clear coat. VOC: Base (e.g. F4161): 472.5 g/lt or 3.9 lbs/gallon Converter (G3010): 591 g/lt or 4.9 lbs/gallon Page 1 of 3 • Rev 11 – October 2014 • AWCRAFT 2000 Metallics

カタログの1ページ目を開く
AWLCRAFT 2000 METALLICS - 2

PRODUCT DATA SHEET AWLCRAFT 2000 METALLICS Application Equipment Conventional air atomized spray or HVLP spray. Metallic urethanes are spray only. SPRAY EQUIPMENT Pressure Pot System Devilbiss or equivalent: Spray Gun: JGA-510 Fluid Nozzle: FX – 1.1 Fluid Needle: 1.1 Air Nozzle: 704 PP PSI: 8-12 PSI GUN PSI: 50-60 PSI Cup Gun System SATA jet 3000 RP: Needle / Nozzle: 1.3 mm PSI: 35 PSI HVLP may not provide enough atomization to get uniform distribution of the pearl or metallic particle. Additional reduction may be needed with HVLP equipment. Standard conventional, air atomized spray gun is...

カタログの2ページ目を開く
AWLCRAFT 2000 METALLICS - 3

PRODUCT DATA SHEET AWLCRAFT 2000 METALLICS After achieving the desired color, allow the coating to cure a minimum of 12 hours but not more than 24 hours. The last coat of metallic should be fully dry to touch to prevent mottling of the metallic. Within this period, seal the AWLCRAFT 2000 metallic with AWLCRAFT 2000 Gloss Clear (F3029/G3010). Mix by volume two parts F3029 AWLCRAFT 2000 Clear with one part AWLCAT #2 (G3010) Spray Converter to a smooth, homogenous mixture. Reduce 25-33% with T0001 or T0002 Reducer. Overall mix is 2:1:1 by volume for example: 8 oz. Base, 4 oz. G3010, 4 oz....

カタログの3ページ目を開く

Awlgripのすべてのカタログとパンフレット

  1. Max Cor CF Primer

    2 ページ

  2. 545

    2 ページ

  3. AWLBRITRE

    2 ページ

  4. Awlcare

    2 ページ

  5. Awlcraft SE

    3 ページ

  6. AWL®COAT TPC

    2 ページ

  7. Wash Primer CF

    2 ページ

  8. Satin Matt

    3 ページ

  9. Griptex

    3 ページ

  10. Awlgrip Topcoat

    2 ページ

  11. Crater-X

    2 ページ

  12. Awlfair LW

    3 ページ

  13. Awlfair Pumpable

    2 ページ

  14. Surface Cleaner

    2 ページ

  15. D3200 D6200

    4 ページ

  16. Awlfair LW Fast US

    2 ページ

  17. Awlcoat TPC

    2 ページ

  18. Alumiprep 33

    1 ページ

  19. Awlwood

    5 ページ

  20. Awlcare

    2 ページ

  21. Awlwash

    2 ページ

  22. Awlfair LW fast EU

    2 ページ

  23. 345 HS PRIMER

    3 ページ

  24. 321 HS UNDERCOAT

    3 ページ

  25. Awlcraft SE

    3 ページ

  26. Activators

    2 ページ

  27. 345HS Primer

    3 ページ

  28. Awlcraft 2000 VOC

    2 ページ

  29. Pro-Cure

    2 ページ

  30. REDUCERS

    3 ページ

  31. Awlbrite Quick-Fil

    2 ページ

カタログアーカイブ

  1. AWL®COAT TPC

    2 ページ

  2. AWLGRIP

    6 ページ

  3. CF 2K

    3 ページ