Awlcoat TPC
1 / 2ページ

カタログの抜粋

Awlcoat TPC - 1

PRODUCT DATA SHEET AWL®COAT TPC WP101 Features & Uses Awl-Coat TPC is a water-based, temporary peelable coating that serves to protect surfaces from damage or contamination. Awl-Coat TPC provides a tough film that guards against scuffing, abrasion and contamination such as overspray, acid rain, fly rust or sanding dust. The product is primarily developed as a solution for boat builders in production or refit environments. Awl-Coat TPC may be applied over Awlgrip and Awlcraft 2000 topcoats. Specification Data Type: Vinyl Acrylic. Packaging: Available in 5 gallon containers. Theoretical Coverage: Sq. Feet/Gallon: 267 - 160 ft²/gl at 3-5 mils dry (4 – 7 m²/lt at 75 - 125 microns dry). Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and environment. Recommended Wet Film Thickness: 6-10 mils (150-250 microns) per coat. Recommended Dry Film Thickness: 3-5 mils (75-125 microns) per coat. A minimum of 3 mils (75 microns) is recommended to ensure easy removal. To increase resilience to wear damage (abrasion, etc) a higher film build is recommended (5-10 mils/ 125 -250 microns dry film thickness). This may require a two coat application. Recoatability at 59ºF/15 ºC: Minimum (with itself): 30 mins (touch dry). Max time: indefinite. Recoatability at 75ºF/25ºC: Minimum (with itself), 20 mins (touch dry). Max time ; indefinite. High Humidity will extend the dry time. Peel time* (at 55 - 104ºF / 13 - 40ºC) : 1 hour. Awlcoat TPC should not be left on the painted surface for more than 4 months. *This is the minimum time required in which sufficient film strength has developed to facilitate the peeling process. Peel times beyond those quoted will allow further film strength development to take place and subsequently improve peeling efficiency. Do not apply other Awlgrip products over Awl-Coat TPC. VOC: Light gray WP101 – 55 g/lt / 0.46 lbs per gallon. All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. ©AkzoNobel 2015 Page 1 of 2 - Rev 6 – January 2015

カタログの1ページ目を開く
Awlcoat TPC - 2

PRODUCT DATA SHEET AWL®COAT TPC WP101 Airless Equipment Orifice Size: 0.017” -0.021” (0.43 – 0.53mm) Total output fluid pressure at spray tip not less than 1500 psi (105kg/cm²) Fan width: 12” (30cm) Pump ratio: 33:1 to 45:1 Surface Preparation Awl-Coat TPC is suitable for application over Awlgrip and Awlcraft 2000 topcoats. It is important that the coating materials have undergone sufficient cure to ensure properties such as gloss and color are not affected by the application of Awl-Coat TPC. The surface of Awlgrip or Awlcraft 2000 should be clean, dry (cured) and free from contaminants....

カタログの2ページ目を開く

Awlgripのすべてのカタログとパンフレット

  1. Max Cor CF Primer

    2 ページ

  2. 545

    2 ページ

  3. AWLBRITRE

    2 ページ

  4. Awlcare

    2 ページ

  5. Awlcraft SE

    3 ページ

  6. AWL®COAT TPC

    2 ページ

  7. Wash Primer CF

    2 ページ

  8. Satin Matt

    3 ページ

  9. Griptex

    3 ページ

  10. Awlgrip Topcoat

    2 ページ

  11. Crater-X

    2 ページ

  12. Awlfair LW

    3 ページ

  13. Awlfair Pumpable

    2 ページ

  14. Surface Cleaner

    2 ページ

  15. D3200 D6200

    4 ページ

  16. Awlfair LW Fast US

    2 ページ

  17. Alumiprep 33

    1 ページ

  18. Awlwood

    5 ページ

  19. Awlcare

    2 ページ

  20. Awlwash

    2 ページ

  21. Awlfair LW fast EU

    2 ページ

  22. 345 HS PRIMER

    3 ページ

  23. 321 HS UNDERCOAT

    3 ページ

  24. Awlcraft SE

    3 ページ

  25. Activators

    2 ページ

  26. 345HS Primer

    3 ページ

  27. Awlcraft 2000 VOC

    2 ページ

  28. Pro-Cure

    2 ページ

  29. REDUCERS

    3 ページ

  30. Awlbrite Quick-Fil

    2 ページ

カタログアーカイブ

  1. AWL®COAT TPC

    2 ページ

  2. AWLGRIP

    6 ページ

  3. CF 2K

    3 ページ