カタログの抜粋

545 - 1

Product Data Sheet 545 Epoxy Primer D8001/D3001 or D1001/D3001 Intended Uses 545 Epoxy Primer is a two component epoxy primer with outstanding corrosion and adhesion properties for steel, aluminum, wood, and fibreglass substrates. 545 Epoxy Primer is used to seal surfacing primers before applying topcoats. It may be applied by spray, brush, or roller and may be used above or below the waterline. Specification Data Volume Solids Specific Gravity Available Packs Base Converter Reducer Equipment Cleaning Typical Shelf Life 39% (unthinned) 1.20 1 US Quart, 1 US Gallon D8001 White Base, D1001 Gray Base D3001 Converter T0006 (Spray), T0031 (Brush) T0002, T0006 2 years Theoretical Coverage Application Methods Brush, Roller Theoretical Coverage Per Coat (at recommended DFT) After sanding, the minimum recommended DFT ~75 µm (3 mil). A further coat may be necessary to achieve the minimum DFT. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size and application environment. VOC All VOC information contained herein is theoretical (unless otherwise stated). Actual VOC content may vary by batch and when tested via standard test methodology. Product As Supplied (without reducer) g/L Surface Preparation The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation. GRP: Remove all surface contamination (waxes, mold release products, dirt, grease etc). Sand with P150 - P220 grade (grit) paper. Steel: Grit blast to white metal in accordance with SSPCSP10 (Sa 2½) to a 23 mils (5075 microns) profile. Aluminium: Grind with 36 grit disc or blast to bright, clean aluminium. The metal must be bright silver and completely free of gray oxidation. The surface profile must be a 2-3 mils profile (50-75 microns). Wood: The wood should be clean and dry. Sand the surface with 80-120 grit paper. Blow off the surface with clean, dry compressed air while wiping with clean rags to remove sanding and dust residue. Mixing & Reduction Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full-scale application is recommended. Application Methods Recommended Thinning Spraying Viscosity Brush, Roller Mix by volume one part Base with one part Converter to a smooth, homogenous mixture. Brush Below 25°C (77°F) you may use COLD CURE Accelerator (M3066) to maintain dry and cure times. Induction Time after Mixing = 15 Minutes. Application Application equipment and parameters are given as a guide. Actual equipment choices will vary according to application conditions, equipment condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service representative for further advice if necessary. For wood substrates, first seal the wood with a light coat of 545 Epoxy Primer (spray) reduced 40% with T0006. Allow to cure for 12-16 hours. Application Methods Fluid Pressure Air Atomized 1.00 - for further 1.8 - 2.2 bar Please refer to your local representative or visit http://www.awlgrip.com1.40 mm information. 39 - 55 thou 26 - 32 psi Awlgrip, the AkzoNobel logo and other products mentioned in this publication are trademarks of AkzoNobel. ©AkzoNobel 2019 Fluid Flow Rate Recoatability & Drying Times The data given for recoatability is not exhaustive. Actual recoatability can vary according to individual conditions, climate and surroundings. If unsure, c

カタログの1ページ目を開く
545 - 2

Mix by volume one part Base with one part Converter to a smooth, homogenous mixture. Brush Below 25°C (77°F) you may use COLD CURE Accelerator (M3066) to maintain dry and cure times. Induction Time after Mixing = 15 Minutes. Product Data Sheet Application Application equipment and parameters are guide. application conditions, equipment condition and 545 Epoxy Primer non-critical area given asbea carried Actual equipment choices will vary according tolocal technical service representative for further other factors. Testing on a should out prior to full-scale application. Contact your advice...

カタログの2ページ目を開く

Awlgripのすべてのカタログとパンフレット

  1. Max Cor CF Primer

    2 ページ

  2. AWLBRITRE

    2 ページ

  3. Awlcare

    2 ページ

  4. Awlcraft SE

    3 ページ

  5. AWL®COAT TPC

    2 ページ

  6. Wash Primer CF

    2 ページ

  7. Satin Matt

    3 ページ

  8. Griptex

    3 ページ

  9. Awlgrip Topcoat

    2 ページ

  10. Crater-X

    2 ページ

  11. Awlfair LW

    3 ページ

  12. Awlfair Pumpable

    2 ページ

  13. Surface Cleaner

    2 ページ

  14. D3200 D6200

    4 ページ

  15. Awlfair LW Fast US

    2 ページ

  16. Awlcoat TPC

    2 ページ

  17. Alumiprep 33

    1 ページ

  18. Awlwood

    5 ページ

  19. Awlcare

    2 ページ

  20. Awlwash

    2 ページ

  21. Awlfair LW fast EU

    2 ページ

  22. 345 HS PRIMER

    3 ページ

  23. 321 HS UNDERCOAT

    3 ページ

  24. Awlcraft SE

    3 ページ

  25. Activators

    2 ページ

  26. 345HS Primer

    3 ページ

  27. Awlcraft 2000 VOC

    2 ページ

  28. Pro-Cure

    2 ページ

  29. REDUCERS

    3 ページ

  30. Awlbrite Quick-Fil

    2 ページ

カタログアーカイブ

  1. AWL®COAT TPC

    2 ページ

  2. AWLGRIP

    6 ページ

  3. CF 2K

    3 ページ