CONUS MST18240
1 / 12ページ

Registered Community Design Operating instructions

The CONUS series underwater lights are designed to use the latest LED lighting The surface-mount designed casings enable very simple installation on the hull without making any bigger holes through the hull under water line. By the help of slope-truncated cone designed casing the CONUS series underwater lights can be installed on the hull to light in different directions, to the sea ground and to the both sides of the yacht. All the models are available in aluminium bronze and anodized aluminium casings in different colors. The lighting is available in white, blue or green colors or...

Underwater Light CONUS MST18240 The 6 mm depth tempered glass optical window. (2) Underwater light casing Aluminium bronze or anodized aluminium casing with fixing holes and cable gland. The 8-pole multi-core cable to connect the power supply unit. The fixing screws to fix the underwater light on the hull.

Power Supply Unit MPSO6800 Terminal-block connector to connect optional remote control unit or switch. Terminal-block connector to connect the LED underwater light using 8-pole multi-core cable. Terminal-block connector to connect 12-24Vdc power supply. Terminal-block connector to connect to the DC IN connector of another power supply unit.

The underwater light kit consists of the following components: • Underwater Light CONUS MST18240 • Power Supply Unit MPS06800 • Operating Instructions with Declaration of Conformity and Warranty conditions Underwater Light CONUS MST18240 The CONUS MST18240 has to be installed on a flat surface on the stern of the hull of the vessel. Do not try to install the underwater light while the vessel is in the water. When the installation is finished briefly test the underwater light prior to launching the vessel. The installation have to be realized by a qualified personnel. • Avoid using the...

♦ Ali the stainless steel fixing screws it is highly recommended to be sealed in the contact with underwater light casing by optional TEF-GEL™ waterproof paste (not included) to prevent galvanic corrosion. • To install the underwater light on the steel hull it is highly recommended to use the optional isolation board (not included) between the hull and underwater light casing to prevent galvanic corrosion. • Do not overtighten the screws as this can result in hull or underwater light damage. The underwater light has to be connected to the vessels bonding and cathodic protection using a pre-...

• The main DC power supply of the vessel has to be switched off before installation. Power supply connection The power supply has to be connected through the switch (not included) and protected by a fuse (not included) to the DC IN terminal-block connector with correct polarity. The power supply voltage has to A power supply unit of another underwater light can be connected to the DC OUT terminal-block • Only one additional power supply unit of the same model number can be connected to the DC OUT terminal-block connector and suitable power supply cable should be used. The appurtenant cap...

TECHNICAL SPECIFICATIONS LED Underwater Light CONUS MST18240 Power requirement Lens angle Optical window Luminous flux White color temperature Operating temperature Power Supply Unit MPS06800 Input voltage Operating temperature 6 mm depth tempered glass Aluminium bronze (AB2) or anodized aluminium Design and specifications subject to change without notice.

1.The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be detective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement of...

Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in Manufacturer's Address: Dutovlje 138 declares that the products item. Product Name and Model Number: 1. Underwater Light CONUS MST18240 with Power Supply Unit MPS06800 conform to the lollowing Product Speciiications: Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CE- marking accordingly:

ASTEL d .0.0.. Du to vi je 138, 6221 Dutovl je. Slovenia E-mail: info(a>astel-marine.com