MAB Solids-retaining Centrifugal Separator
1 / 2ページ

{{requestButtons}}

カタログの抜粋

MAB Solids-retaining Centrifugal Separator - 1

Solids-retaining Centrifugal Separator Purification or clarification of mineral oils used In marine installations and power stations (fuel and lubricating oils). Working principle Separation takes place in a solids-retaining bowl that can be arranged for either clarification or purification. In both cases, the contaminated oil Is fed into the separator through the centre, and It is separated by centrifugal force Into its various phases, the heaviest phase (sludge and water) being forced outwards to the periphery of the bowl. The accumulation of sludge is periodically removed from the bowl by hand. The oil is pumped, heated, and separated as shown In the figure. A liquid seal In the separator bowl prevents the oil from escaping through the water outlet. If this seal Is broken, an alarm device is activated. With unmanned engine rooms, the signals are transmitted to a remote control unit. When the seal is broken, the three-way valve shuts off the oil feed and separator model MAB 103B complete with feed/discharge pump the oil Is recirculated until the fault Is corrected. and fittings for connection to a preheater. D. Oil from separator outlet three-way valve 4. Plate heat exchanger 9. Liquid-seal alarm cabinet Schematic installation layout of MAB separator with plate-type oil heater.

カタログの1ページ目を開く
MAB Solids-retaining Centrifugal Separator - 2

Water outlet MAB bowl arranged as a clarifier for separating oils containing sludge and a very small quantity of water. MAB bowl arranged as a purifier for separating oils containing sludge and an appreciable quantity of water. Standard design Solids-retaining separator comprising a frame containing in its lower part a horizontal drive shaft with friction clutch and brake, worm gear and a vertical bowl spindle. The worm gear is placed spindle inside the space formed by the upper part of the frame and the frame hood which also carries the feed and discharge systems. The frame hood is hinged...

カタログの2ページ目を開く

Alfa Laval Mid Europeのすべてのカタログとパンフレット

  1. i-40D

    4 ページ

  2. PureBilge

    20 ページ

  3. Eliminator – CCU

    4 ページ

  4. Vibration dampers

    2 ページ

  5. F-152

    4 ページ

  6. AlfaBlue Junior DG

    16 ページ

  7. EPC 60 Retrofit

    2 ページ

  8. Always a step ahead

    12 ページ

  9. PureNOx Prime

    4 ページ

  10. LPG carriers

    2 ページ

  11. LNG carriers

    2 ページ

  12. PureNOx

    2 ページ

  13. Marine Essentials

    100 ページ

  14. Fincoil Solar Max

    10 ページ

  15. Aalborg TFO

    10 ページ

  16. Aalborg OC

    2 ページ

  17. Aalborg D

    2 ページ

  18. Aalborg KBE

    2 ページ

  19. Compabloc

    4 ページ

  20. AlfaBlue BXM/BXD

    2 ページ

  21. Alfa-V ACV

    2 ページ

  22. PureSOx

    16 ページ

  23. PureDry

    4 ページ

  24. PureBallast 3.0

    6 ページ

  25. Heating Insulation

    2 ページ

  26. CB100 / CBH100

    2 ページ

  27. Alfa Laval AOT 3F

    2 ページ

  28. AlfaRex - TM20

    2 ページ

  29. AlfaDisc

    2 ページ

  30. AlfaCond range

    2 ページ

  31. Eliminator CCU

    4 ページ

  32. MIB 303

    4 ページ

  33. EMD00062EN Emmie

    2 ページ

  34. PureBilge system

    38 ページ

  35. Here30_ENG.pdf

    36 ページ

カタログアーカイブ