カタログ >
Alfa Laval Mid Europe >
Flex separation systems, P separators 626/636

Flex separation systems, P separators 626/636
1 / 6ページ

カタログの抜粋

Flex separation systems, P separators 626/636 - 1

Flex separation systems, P separators 626/636 Cleaning systems for lubricating and lighter fuel oils* Separator Control cabinet including EPC 60 and optional starter * P separators 626/636 can also be used to clean heavier oils with well-defined densities. S and P Flex separation systems Alfa Laval’s S and P Flex separation systems combine the high efficiency, low sludge output and low operating cost of Alfa Laval centrifugal separators with a flexible scope of supply. Extensive possibilities for the separation system layout and assembly make it possible to suit any engine room and any oil separation application. In addition, S and P Flex separation systems feature the EPC 60 controller, which enables the intuitive navigation of menus, parameters and alarms. The EPC 60 controller also has a modular construction for easy I/O board addition and replacement. The S and P Flex separation concept includes the complete S- and P separator range. These can be combined in mixed ship sets, even within a single customer-specified module. Change-over valve Water block Flex system components for P separators 626/636. Application P separators P separators are based on purifier technology, which means that the oil/water interphase is manually adjusted by means of a gravity disc. Because the separators do not automatically adjust to varying oil density, they are most suitable for economicalcleaning of the following: • Lubricating oils • Distillates • Lighter diesel oils If the oil is well defined and does not vary in den ity, P sepa s rators can also be manually adjusted to clean heavy fuel oils with densities up to 991 kg/m3 and viscosities up to 700 cSt/50ºC. P separators are designed for automatic operation at sea and in automated power stati

カタログの1ページ目を開く

Flex separation systems, P separators 626/636 - 2

Scope of supply The S and P Flex separation concept provides a wide range of alternatives for P separators. Depending on the need, a P separator can be supplied as a separator and ancillaries, as a customer-specified module, or as part of a comprehensive ackage including services p and order-specific documentation. These P separators come equipped with energyefficient IE3 motors. Module examples Single Flex module with separator (excluding heater and pump) Single Flex module with separator, heater and pump Flex system A P separator with ancillaries in the form of optimized block...

カタログの2ページ目を開く

Flex separation systems, P separators 626/636 - 3

Optional equipment Flex separation systems based on P separators 626/636 can be complemented with the following equipment: • Starter (included in module versions) • HEATPAC heaters • Space heating • Additional thermometers • Vibration sensor kit • ALP feed pump • Flow regulating system • Sludge removal kit • Sludge outlet butterfly valve kit • Steam shut-off valve kit • Air pressure reducer valve • ipe arrangement for multiple modules, P including heater cross-connection • Emergency safety shutdown • Remote monitoring and control • Separator lifting tool Schematic diagram 1 Feed pump 2...

カタログの3ページ目を開く

Flex separation systems, P separators 626/636 - 4

System layout 1. Feed pump 2. Heater 3. Pneumatically controlled change-over valve 4. Pressure transmitter 5. Control unit 6. Regulating valve 7. Solenoid valve block, water Operating principle A Flex separation system based on a P separator 626/636 is operated automatically by the EPC 60 controller. Untreated oil, heated to the correct temperature, is fed continuously to the separator, which is driven by an electric motor via a friction clutch and belt. The separator bowl is fixed at the top of a spindle, which is supported by bearings and special composite springs. This bowl can be...

カタログの4ページ目を開く

Flex separation systems, P separators 626/636 - 5

CentriShoot Instead of a sliding bowl bottom, the CentriShoot discharge system features a fixed discharge slide that flexes at its edge. This increases discharge accuracy and does away with metal-to-metal wear. CentriLock Conventional lock rings are threaded and must be removed with a sledgehammer. Over time, the metal-to-metal wear between bowl and lock ring can lead to expensive bowl repair or replacement. Step one: The CentriShoot discharge slide is fixed at the centre. During separation, the slide covers the discharge ports. An Allen key is the only tool needed to work with CentriLock....

カタログの5ページ目を開く

Flex separation systems, P separators 626/636 - 6

Operations Preventive maintenance procedures are handled quickly and simply with the help of a compression tool. The snap ring of the patented CentriLock bowllocking system is non-threaded and requires only an Allen key to remove. • Maintenance intervals: - Inspection Service every 4 000 h or 6 months - Overhaul Service every 12 000 h or 18 months • Service spares kits contain all necessary spare parts for each service and tips for maintenance in checkpoints: - Inspection Kit with O-rings and seals for separator bowl - Overhaul Kit with parts for drive system, belt, bearings and pads, also...

カタログの6ページ目を開く