SV38
4Pages

{{requestButtons}}

Catalog excerpts

SV38 - 1

SV38 Weld-in LED Tank Light Introduction: Congratulations on the purchase of your new weld-in LED tank light for use inside ballast and fresh water tanks in steel or aluminum hulled vessels*. Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish and/or for security and safety. *Weld-in front flange material and angular range must be specified. General Operating Information: The latest commercial grade “COB” High-Density Light Emitting Diode (LED) technology used in this light will provide robust and reliable operation under normal operating conditions when used with the matching Underwater Lights® USA, LLC driver. This light is equipped with thermally protected circuitry and can be operated above or below the water. Optimum performance and longevity will be achieved when operating underwater. The main body is designed and tested to act as a cofferdam for added security. Depending upon water clarity conditions, the light beam can reach up to 30 meters (100 feet). General Safety Information: This light must be welded into a steel or aluminum hulled vessel in accordance with common ship building practices. Never try to install or remove this light while the vessel is in the water or if the light is surrounded by water. Upon proper installation, this light will become part of the vessels grounding and cathodic protection system. Always disconnect and lock-out power before working on light. The light should be inspected for moisture intrusion every six months. The lights electrical cabling and driver box should be visually inspected for proper operating condition every six months. Marine growth should be removed from the glass using a soft brush to allow both heat and illumination to exit the light. Technical Specifications: Light source = Instant on high flux density LED array - 14,630 Lumens - 7000 Kelvin color temperature - 40,000+ hours life Glass = Borosilicate glass - 12.7mm (0.5”) thick - 58mm (2.3”) diameter net aperture Light Common Body Dimensions = 150mm (5.9”) diameter x 120mm (4.7”) long Smallest Front Flange Dimensions = 100mm (3.94”) diameter x 25mm (0.98”) long Largest Front Flange Dimensions = 140mm (5.51”) diameter x 213mm (8.39”) long Construction (STEEL) = 316L Stainless steel - 955 Bronze Construction (ALUMINUM) = Bright dip anodized 5086 marine aluminum - 955 Bronze Power supply = See matching Underwater Lights® USA, LLC driver box Troubleshooting: Please contact our Florida technical support staff at 1-954-760-4447 or French technical support staff at +33 (0) 497 21 0296, Monday thru Friday from 8:00 am to 5:00 pm local time. Warranty: Underwater Lights® USA, LLC warrants this light to be free from defects in workmanship and materials for a period of two years from the date of original purchase. Further, misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should your light prove defective during the warranty period, promptly contact Underwater Lights® USA, LLC for an RMA number and then return the light freight prepaid with the RMA number clearly marked on the outside of the shipping container. Underwater Lights USA, LLC 1881 W State Road 84, Bay 102 Fort Lauderdale, FL 33315 USA Phone: 1-954-760-4447 Fax: 1-954-525-3261 Internet: www.seavision.com Email: sales@seavision.com Underwater Lights Europe Sarl 16, rue Rouaze 06400 Cannes, France Phone: 33-(0)-4-97-21-02-96 Fax: 33-(0)-4-97-21-10-96 Internet: www.seavision.com Email:

Open the catalog to page 1
SV38 - 2

Weld-in LED Tank Light STEEL/ALUMINUM This light should be installed at minimum 250-300mm (10-12") below the light load water line with approximately a 20° down angle by qualified/approved personnel using proper tools, welding procedures and materials. An access area of at least 100mm (3.94") should be left behind the light for lamp servicing and light cooling. After selecting a location, cut an appropriate sized hole through the vessel hull. Note: Hole size will be defined by the specific weld-in Front Flange (13) that came with the light. Caution! Check that no electrical wiring, fuel...

Open the catalog to page 2
SV38 - 3

Introduction: Congratulations on the purchase of your new thru hull LED light driver box. Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. Features Include: Latest control technology and electronic component construction to guarantee high levels of performance. Universal VAC input with short circuit, over current, over voltage and over temperature protections. Electrical wiring...

Open the catalog to page 3
SV38 - 4

Installation: The driver box should be mounted in a cool, dry, well ventilated and easily accessible location. Attach the driver box to a fixed bulkhead or similar secure structure using appropriate M6 fasteners with adequate space between driver boxes for proper cooling. Note: Whereas the driver box can be placed in any orientation, it is recommended that the cable strain relief connectors face down. Using marine grade 16/3 cable, run a VAC input line into the driver box and secure by way of one cable strain relief connector. Run the marine grade 18/2 cable supplied with the thru hull LED...

Open the catalog to page 4

All Underwater Lights - Sea Vision catalogs and brochures

  1. SV10 HID

    5 Pages

  2. DV59

    3 Pages

  3. SV31

    2 Pages

  4. SV14 HID

    7 Pages

  5. SV60

    7 Pages

  6. SV14 LED

    6 Pages

  7. DV80

    1 Pages

  8. SV27

    3 Pages

  9. SV37

    9 Pages

  10. SV14alum

    5 Pages

  11. SV37PlasmaUS

    12 Pages

  12. SV37LED

    3 Pages

  13. SV 44

    3 Pages

  14. SV16

    3 Pages

  15. SV20

    3 Pages

  16. SV19

    3 Pages

  17. SV19 LED

    3 Pages

  18. SV10-250W

    3 Pages

  19. SV10-150W

    3 Pages

  20. DV 30

    1 Pages

  21. DV 29

    1 Pages

  22. DV 28

    1 Pages

  23. DV 26

    1 Pages

  24. DV 23

    1 Pages

  25. SV 38

    1 Pages

  26. SV 37

    1 Pages

  27. SV 42

    1 Pages

Archived catalogs

  1. DV 24

    5 Pages

  2. SV38

    3 Pages

  3. SV 14 LED

    3 Pages

  4. SV 43

    3 Pages

  5. DV 41

    1 Pages