SV37PlasmaUS - 12 Pages

Add to MyNauticExpo favorites
SV37PlasmaUS

Catalog excerpts

 he Sea Vision SV37 Plasma weld in model for aluminum or steel hulls can be installed in the transom or the hull, it utilizes a light emitting plasma (LEP) light source and 110 or 230 volt AC power. LEPs are the next generation of high intensity lighting. Sea Vision has adapted this technology to become the successor to their metal halide line of underwater lighting for mega yachts. The lights can be welded at adjustable angles to suit all hull shapes. The hull shape and positioning will dictate the angle of the light you require, angles available are 0 to 50 degree. Patent Pending SV37 technical specifications Application for: Aluminum or Steel hulls ——————————————————————— Lamp: Light Emitting Plasma ——————————————————————— Life length: approx. 30,000 hours ——————————————————————— Lumens: 23,000 ——————————————————————— Kelvin color temp: 5750 ——————————————————————— Glass lens: Borosilicate glass ——————————————————————— Thickness: 20mm / 0.79” ——————————————————————— Power supply: 100 – 240 VAC, 4.0 – 1.5 Amps, ——————————————————————— Casing material: Aluminum 5086 / Stainless Steel 316L ——————————————————————— Angles available: Flush 30 degree 24 – 38 degree 38 – 50 degree ——————————————————————— Code: SV37 Plasma ——————————————————————— Installation: Recommended at least 10” (250mm) below the light load waterline and between 9 and 16 feet (3 -- 5 meters) apart. This is a guideline only, for specific requirements please contact us. ——————————————————————— Note: All information is subject to change without prior notice, please confirm details prior to ordering. 1881 W. State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 sales@seavision.com www.seavision.com

 Open the catalog to page 1

Congratulations on the purchase of your new weld-in light for ALUMINUM hulled vessels. Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to "enhance your boating experience". These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The emitter module in this product utilizes a rapid start and re-strike plasma light source. This means that it must be allowed to cool for approximately 2 minutes after being shut off before being restarted....

 Open the catalog to page 2

Installation: This light h ld be installed t i i Thi li ht should b i t ll d at minimum 250 300 250-300mm (10 12”) b l (10-12”) below th li ht l d water li the light load t line b qualified/approved personnel by lifi d/ d l using proper tools, welding procedures and materials. An access area of at least 75mm (3”) should be left behind the light for lamp servicing and general ventilation. After selecting a location, cut an appropriate sized hole through the vessel hull. Note: Hole size will be defined by the specific weldin Front Flange (12) that came with the light. Caution! Check that no...

 Open the catalog to page 3

Introduction: Congratulations on the purchase of your new weld in light for STEEL hulled vessels Underwater Lights® USA LLC takes pride in weld-in vessels. USA, providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The emitter module in this product utilizes a rapid start and re-strike plasma light source. This means that it must be allowed to cool for approximately 2 minutes after being shut...

 Open the catalog to page 4

Installation: This light h ld be installed t i i Thi li ht should b i t ll d at minimum 250 300 250-300mm (10 12”) b l (10-12”) below th li ht l d water li the light load t line b qualified/approved personnel by lifi d/ d l using proper tools, welding procedures and materials. An access area of at least 75mm (3”) should be left behind the light for lamp servicing and general ventilation. After selecting a location, cut an appropriate sized hole through the vessel hull. Note: Hole size will be defined by the specific weldin Front Flange (12) that came with the light. Caution! Check that no...

 Open the catalog to page 5

SV37, Plasma Light Driver Assembly Introduction: Congratulations on the purchase of your new driver assembly for your Underwater Lights™ USA, LLC plasma weld-in light. Underwater Lights™ USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. Features Include: Latest microprocessor control technology to guarantee high levels of performance. Provides flicker free power to matching plasma weld-in light...

 Open the catalog to page 6

All Underwater Lights - Sea Vision catalogs and brochures

  1. SV10 HID

    5 Pages

  2. DV59

    3 Pages

  3. SV31

    2 Pages

  4. SV14 HID

    7 Pages

  5. SV38

    4 Pages

  6. SV60

    7 Pages

  7. SV14 LED

    6 Pages

  8. DV80

    1 Pages

  9. SV19 LED GEN II

    3 Pages

  10. SV27

    3 Pages

  11. SV38

    3 Pages

  12. SV37

    9 Pages

  13. SV14alum

    5 Pages

  14. SV37LED

    3 Pages

  15. SV 44 SURFACE

    3 Pages

  16. SV 44

    3 Pages

  17. SV42-Thru Hull

    3 Pages

  18. SV16

    3 Pages

  19. SV20

    3 Pages

  20. SV19

    3 Pages

  21. SV19 LED

    3 Pages

  22. SV10-250W

    3 Pages

  23. SV10-150W

    3 Pages

  24. DV 30

    1 Pages

  25. DV 29

    1 Pages

  26. DV 28

    1 Pages

  27. DV 26

    1 Pages

  28. DV 23

    1 Pages

  29. SV 38

    1 Pages

  30. SV 37

    1 Pages

  31. SV 42 THRU HULL

    1 Pages

  32. SV 42

    1 Pages

Archived catalogs

  1. DV 24

    5 Pages

  2. SV 14 LED

    3 Pages

  3. SV 43 THRU HULL

    3 Pages

  4. SV 43

    3 Pages

  5. DV 41

    1 Pages