Catalog excerpts
SIGMATHERM 175 2 pages DESCRIPTION October 2009 Revision of September 2005 heat resistant modied alkyd aluminium nish PRINCIPAL CHARACTERISTICS – – – – heat resistant up to 175°C high brilliancy spray application improves the appearance a minimum drying time of 3 days at 20°C should be allowed before exposure to heat COLOURS AND GLOSS aluminium - gloss BASIC DATA AT 20°C (1 g/cm³ = 8.25 lb/US gal; 1 m²/l = 40.7 ft²/US gal) Mass density Volume solids VOC (supplied) 1.0 g/cm³ 47 ± 2% max. 411 g/kg (Directive 1999/13/EC, SED) max. 417 g/l (approx. 3.5 lb/gal) 25 µm per coat 18.8 m²/l for 25 µm 3 hours at 5 - 10°C, 1 hour at 20°C min. 36 hours at 5 - 10°C, 16 hours at 20°C max. unlimited at least 12 months, longer storage period may affect the brilliancy Recommended dry lm thickness Theoretical spreading rate Touch dry after Overcoating interval Shelf life (cool and dry place) RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES – previous coat; (e.g. Sigmarine 24) dry and free from any contamination – substrate temperature should be at least 3°C above dew point SYSTEM SPECIFICATION for heat resistant systems - see system sheet 3140 INSTRUCTIONS FOR USE – stir well before use – the temperature of the paint should preferably be above 15°C, otherwise extra thinner may be required to obtain application viscosity – too much solvent results in reduced sag resistance – adequate ventilation must be maintained during application and curing (please refer to sheets 1433 and 1434) AIRLESS SPRAY Recommended thinner Nozzle orice Nozzle pressure no thinner should be added approx. 0.33 - 0.38 mm (= 0.013 - 0.015 in) 12 - 15 MPa (= approx. 120 - 150 bar; 1700 - 2130 p.s.i.) AIR SPRAY Recommended thinner Volume of thinner Nozzle orice Nozzle pressure Thinner 20-05 0 - 3%, depending on required thickness and application conditions 1.8 - 2 mm 0.3 - 0.4 MPa (= approx. 3 - 4 bar; 43 - 57 p.s.i.) page 1/2
Open the catalog to page 1SIGMATHERM 175 October 2009 BRUSH/ROLLER Recommended thinner no thinner should be added CLEANING SOLVENT Thinner 20-05 SAFETY PRECAUTIONS for paint and recommended thinners see safety sheets 1430, 1431 and relevant material safety data sheets this is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapour as well as contact between the wet paint and exposed skin or eyes Worldwide availability Whilst it is always the aim of PPG Protective & Marine Coatings to supply the same product on a worldwide basis, slight modication of the product is sometimes...
Open the catalog to page 2All Sigma Coatings PPG PMC catalogs and brochures
-
SIGMAGLIDE® 890
2 Pages
-
PPG STEELGUARD™
5 Pages
-
PPG PSX® 700
5 Pages
-
SIGMAPRIME
8 Pages
-
PPG Hydroelectric power
4 Pages
-
PPG HI-TEMP 900
2 Pages
-
PPG FPSO
4 Pages
-
PPG Fossil power
4 Pages
-
PPG Drill ships
4 Pages
-
PITT-CHAR® XP
5 Pages
-
AMERSHIELD®
4 Pages
-
AMERLOCK® SERIES
4 Pages
-
AMERCOAT 240 SERIES
4 Pages
-
SIGMACOVER 280
7 Pages
-
SIGMAWELD™ 120
4 Pages
-
SIGMASHIELD 1200
5 Pages
-
PSX® 700
8 Pages
-
AMERCOAT 205
5 Pages
-
AMERCOAT 114 A
5 Pages
-
ABC 4
4 Pages
-
ABC 3
4 Pages
-
AMERCOAT 242 HB
6 Pages
-
AMERCOAT 242
6 Pages
-
AMERCOAT 238
6 Pages
-
AMERCOAT 237 M
5 Pages
-
AMERCOAT 138 G
5 Pages
-
SIGMASHIELD 1090
5 Pages
-
SIGMASHIELD 1200
5 Pages
-
SIGMATHERM 500
3 Pages
-
SIGMAWELD 165
5 Pages
-
SIGMAWELD 190
5 Pages
-
SIGMATHERM 540
3 Pages
-
NOVAGUARD 840
5 Pages
-
SIGMA ECOFLEET® 690
2 Pages
-
PHENGUARD 935 EN
5 Pages
-
SIGMA ALPHAGEN 240 EN
5 Pages
-
SIGMACOVER 435 EN
6 Pages
-
SIGMADUR 580 EN
4 Pages
-
SIGMAGUARD 720 EN
4 Pages
-
SIGMADUR ONE
3 Pages
-
SIGMAGLIDE 990
3 Pages
-
SIGMAGUARD CSF 650
6 Pages
-
SIGMARINE 42
2 Pages
-
SIGMAZINC 102
4 Pages
-
SIGMAWELD 199
4 Pages
-
SIGMA VIKOTE 18
3 Pages
-
SIGMASHIELD 420 LT
4 Pages
-
SIGMARINE 28
3 Pages
-
SIGMAGUARD 425
4 Pages
-
SIGMA ECOFLEET 238 A
3 Pages
-
SIGMADUR 500US
4 Pages
-
SIGMACOVER 520
4 Pages
-
SIGMACOVER 380
4 Pages
-
SIGMA AQUACOVER 45
3 Pages
-
SIGMA ALPHAGEN 230
5 Pages
-
PHENGUARD 930
5 Pages