Catalogue Oil Change/ Winterizing System
www.shurflo.com
print switch display
Page / 3
Contact the
Manufacturer
Where to buy
this product ?
Request
a Quote
Shurflo - 162567, 4728, 16486
/ 3
See other catalogues for Shurflo
Text version of the page
This brief installation guide for SHURfo pump systems will answer the most often encountered questions about basic marine plumbing systems. Additional more detailed information is available through technical data sheets from SHURfo, as well as the installation instruction sheets provided with each product. ^^^^^^^^^B
For more information, contact your SHURfo representative or SHURfo customer service toll free at
West of the Rockies: (800) 854-3218 East of the Rockies: (800) 762-8094
General Notes
 All SHURflo pumps are engineered with rubber ^^■tng feet to minimize noise and vibration and will
properly only if proper fasteners are used to | snug down (not flatten) the feet. Flexible mounting, as well as flexible inlet and outlet plumbing (such as reinforced hose), is critical to low pump noise level and
pump longevity.
• SHURflo recommends that all pumps be fused
■ individually, in addition to any other circuit protectioi used such as circuit breakers. ^^^■I^^^H
• For all pumps except bilge pimsfaheHmnimum^
■ required tubing is 3/ 8" [10mm] ID., however use 3/4" [19mm] ID. to insure maximum flow.
• All SHURflo marine water pumps are ignition protected
• fa order to minimize heat rise, confinuousl^op^^
■ pumps other than bilge pumps should be mounted in well ventilfa I | BI^^^^^^^^^J
• SHURHo diaphragm pumps will operate in any positioi
■ however, the recommended position is motor up/ pump head down to prevent any possible water damage to I the motor in the event of a leak during setup or operati" Mount on a solid surface to' reduce noise and vibratio|
Htiings in standard hex or wing nut style, straights and elbows fiom sizes 3/ 8" to 3/ ^^H^H
• Waterguard™ filters are great for RV, Marine and B Home applications. The filter may be installed in ar^| ^^jjjj^^^ Be sure to keep the filter away 4™ any heat source. All filters should be replaced seasonally (6-12 months) or when taste and odor problems return. ■
• All SHURflo 2088 & 2093 threaded pump ports B are internally tapered, to be thoroughly hand- M
Iftened only with SHURflo swivel ^^^H They eliminate expensive brass or stainless 1 which require more complex plumbing. ■
• A safety sea-cock (thru-iull valve) is required for
■ any installation using a thru-hull water source. ■
• fa accordance with American Boat and yacht
■ Council (ABYC) guidelines, the recommended |
placement for all diaphragm pumps plumbed to
a thru-hull fitting is above thejwaterlinLi^iM
• The self-priming feature of SHURflo diaphragm
pumps allows them to be mounted any distance up
to 30 feet [9.2m] horizontal fiom on-board water | supplies, insuring easy access to plumbing
and strainers, maximizing reduction of noise or vibration and minimizing exposure to M splashed water. ^^^^^^^^^^H
° Wire Size Requirements [ted on 10 *psw.voitage drop] °
Battery-to-pump distance
Wire
0-10 feet 10-30 feet 30-40 feet 40-50 feet
16 GA 14 GA 12 GA 10 GA
Plumbing Guidelines [For long life and low noise]
SHURflo Fittings Feet Pump/Hose
Water Purifier Noise Reduction
Hand tighten only
3ug, don't flatten; sOid surface
Flexible hose on inlet and outlet sde of pump.
1/2' rrinmum on mans 3/8" minmum on branch
FUui separate line from mans 1/4' minimum recommended
Usa flexible hose. Check for ar in system, inCuding all dran lines
and hot marine water heater lines
(1/ 2"-14 National American Straight Pipe Thread (Except 3000-300; 3000-301 & 3000-400)
NauticExpo's Virtual Library: PDF Catalogues | Documentation | Boating Brochures | Manuals | Marine directory | Specifications | Characteristics
Search Go
page 1 p.1
page 2 p.2
page 3 p.3
pdf-page pdf ne En 2009-01-02-09